background image

1

Getting started

This installation guide describes how to install the air inlet filter and exhaust air kits. For more information, including technical specifications 

or product specifications, visit the product website at www.barco.com or read your projector user manual.
Note! The exhaust air kit is an accessory for Barco F50- and CT- series projectors only.

2

Installation Guidelines

•  The exhaust kit must only be used with ceiling mounted projectors.
•  The air filter kit is sold separately.
•  The exhaust air kit and air inlet filter can be installed separately of one another.
•  If the exhaust is to be directed into a false ceiling, this area must be well-ventilated. However, attention must be paid to ensure that the 

ventilation does not override the projector’s internal fans.

•  Minimum safety distance between the projector (with kit mounted) and the ceiling is at least 15 cm (5.9”). 
•  Do not try to force parts into position; if there is resistance, remove the part, reposition and try again. 
•  Do not overtighten screws.
•  Do not block the air inlet or the exhaust air outlet. 
•  Hot air is exhausted from the rear air outlet. Do not place any heat-sensitive objects in the vicinity of the exhaust vent.

Note! The exhaust air kit is only intended for use with ceiling mounted projectors

Installation

3

 Verify that the installation area meets 

the relevant technical and environmental 

requirements, as illustrated above. 

Position the air inlet filter onto the projector grill, 

making sure that the plastic guide on the filter 

enters the grill properly. Install the filter with a 

M3x8 screw at the right side (reference 1) and two 

M3x14 screws at the left side (reference 2).

Loosen the two ceiling mount fastening screws 

(reference 3 and 4). Remove the center rib. 

Slide the duct into the ceiling mount tracks 

as illustrated. Make sure that the side of the 

duct clicks into position, as shown in the detail 

illustration. Install the rib side screws (reference 

5). Replace and fasten the two ceiling mount 

screws (reference 3 and 4).

Position the ceiling mount cover on the projector 

so that the tabs at the front of the ceiling cover 

enter the slots on the rear of the projector (view 

A). Install and fasten the two screws (reference 6). 

Position the side cover on the projector as 

illustrated. Install two M3x8 screws at the rear 

end of the projector (reference 7) and two M3x20 

screws at the front end of the projector (reference 

8). 

Thread the flexible hose (reference 9) for the 

exhaust air onto the exhaust duct and fasten it 

with the hose clamp (reference 10).

1. Verify installation requirements.

2. Install air inlet filter (optional).

3. Install duct to ceiling cover.

4. Install ceiling mount cover to projector. 

5. Install side cover to projector. 

6. Mount flexible hose. 

Note! Successful installation of the air inlet 

filter will trigger automatic changes in the 

projector software and LFM schedule.

min. 15c

m

must be

≥90⁰

1

1

2

3

4

5

A

6

6

7

8

9

10

1

2

5

4

3

7

6

7

Kit contents

Item Description

1

Hose clamp

2

Flexible hose Ø250mm

3

Ceiling cover

4

Ceiling cover rib

5

Exhaust duct

6

Side cover

Size

Qty Description

PT3x7

2

Ceiling cover rib

M3x6

2

Ceiling cover 

M3x8

2

Side cover

M3x20

2

Side cover

R9801322/R9801323

Fasteners

R9801320/R9801321

Item Description

7

Air inlet filter

Size

Qty Description

M3x8

1

Air inlet filter

M3x14

2

Air inlet filter

Fasteners

601-0326-01

Installation Guide

F50- & CT- Series Exhaust Air Kit & Air Filter Kit

Отзывы: