4. Physical installation
4. PHYSICAL INSTALLATION
Overview
•
•
Suspension of the HDF WLP series projector with rigging clamps
4.1
Power connection
C
AUTION
:
Use only the power cord provided with the projector.
How to connect your projector with the local power net ?
1. Ensure that the power switch (S) stands in the “0” (OFF) position.
2. Connect the power cord (P) with the power input socket of the projector as illustrated below.
3. Secure the power plug by locking the plug holder clamp (H).
4. Connect the other end of the power cord with the local power net.
Caution:
Ensure that the power net meets the power requirements of the projector.
The voltmeter (M) will immediately indicate the value of the mains voltage as soon as the projector is connected with the power
net.
1
2
M
S
H
P
P
M
S
H
Image 4-1
Power connection
Fuses
The projector is protected with an automatic circuit breaker of 35 A which is built in into the power switch.
Volt meter
After few moments, when the projector is fully started up, check if the value indicated by the volt meter is still within the speci
fi
ed
power range of the projector. Note that in case the power net drops signi
fi
cantly during start up, the light source will fail the ignite. If
this is the case, take the necessary measures to reinforce the power net to the projector before starting up the projector again.
Volt meter is protected with a Miniature Fuse, 5 x 20 mm, T 1AH, 250 VAC, UL: 115 V - 300 VDC.
Spare power plug
The projector is delivered with a spare power plug. This spare power plug is attached behind the nameplate of the projector. Remove
the cover of the light source
fi
rst to access this spare power plug. Note that only quali
fi
ed technical personnel may install a new
power plug.
R5906730 HDF WLP SERIES 01/08/2017
29
Содержание HDF-W30LP
