Barco HDF W series Скачать руководство пользователя страница 77

Страница: 77 / 319

8. Input

8.3

Advanced Settings

•

•

•

•

•

•

HDMI - DisplayPort input (3D input module)

8.3.1

About Input Setup

Overview

Each input module must be con

gured before these module can be used. This con

guration is necessary so that the projector knows

which type of signal is connected to its input.

The projector has 4 input slots. Slot 1 and 2 is

lled up by default with a DVI and Dual SDI input. Slot 3 and 4 can be

lled up with

optional input modules. Identical modules are allowed.

8.3.2

Input con

guration

3D item in the Input menu is grayed out when no 3D module is inserted in slot 3 or 4.

How to change?

Press

Menu

to activate the menus and select

Input

→

Advanced Settings

Press

ENTER

The Advanced Settings window is displayed with the actual situation

lled out.

Use the

▲

▼

key to select an input

Press

ENTER

to open the selection menu which will be different from input type to input type.

Image 8-4
Main window

Image 8-5
Advanced input settings

Image 8-6
Advanced settings, input selection

R5905158 HDF SERIES 16/06/2015

Содержание HDF W series
































































































































































































































































































































Результаты поиска

Содержание HDF W series

Отзывы:

Бренды по названию

Популярные бренды

Barco HDF W series, Инструкция по использованию и установке

Результаты поиска

Содержание HDF W series

Отзывы:

Бренды по названию

Популярные бренды