Barco HDF W series Скачать руководство пользователя страница 171

Страница: 171 / 319

12. Alignment

Or,
press

ENTER

when an item is selected and use the 4 arrow keys to adjust.

Image 12-43
Warping, keystone

Move the corner points to the desired position.

Image 12-44
Keystone adjustment

12.7.9 Linearity adjustment, work

Adjusting vertical and horizontal linearity

Select the 2 x 2 adjustment level. See "Setting the warping level", page 164.

The default selected anchor point is the left top corner of the image.

Select the desired warp area.

Depending on the selected area only the points in that area will be adjusted.

Select Linearity.

Select within

Warp Adaptations

Horizontal

Vertical

to adjust the corresponding keystone.

Or,
press

ENTER

when an item is selected and use the 4 arrow keys to adjust.

Image 12-45
Warping, Linearity

Adjust the horizontal and vertical linearity.

ne tune this adjustment, select a speci

c area and add extra anchor points by changing the warp level.

R5905158 HDF SERIES 16/06/2015

167

Содержание HDF W series
































































































































































































































































































































Результаты поиска

Содержание HDF W series

Отзывы:

Бренды по названию

Популярные бренды

Barco HDF W series, Инструкция по использованию и установке

Результаты поиска

Содержание HDF W series

Отзывы:

Бренды по названию

Популярные бренды