Barco DP2K-E series Скачать руководство пользователя

Страница: 37 / 163

6. Lenses & Lens selection

6.2

Lens selection

Which lens do I need?

1. Go to Barco’s website on

www.barco.com

and click on myBarco

2. Login on.

If you are not yet registered create a login and password. With the created login and password, it is possible to enter myBarco.

When your login is correct, the start page is displayed.

3. Click the

Support

tab, then

Digital cinema calculator

(on the left of the screen) and select the appropriate lens calculator.

The lens calculator (see screenshot, image 6-6) will be displayed.

The lens calculator allows you to have an overview of which lenses are suitable for your speci

c projector setup. Just make your

selection of parameters and all possible con

gurations are displayed.

Image 6-6
Digital cinema lens calculator

Take into account that when the projector is tilted the Screen Width you have to

ll in should be larger than

the physical screen width due to the keystone distortion of the projected image. How much larger depends
on the amount of tilt.

Due to production tolerances the real distances can differ by 2% from the calculated values.

For critical situations (

xed installs that use the lens at one of its extreme zoom positions) this should be

taken into account.

R5906693 DP2K-E SERIES 19/06/2015

Содержание DP2K-E series




































































































































































Результаты поиска

Содержание DP2K-E series

Отзывы:

Похожие инструкции для DP2K-E series

Бренды по названию

Популярные бренды

Barco DP2K-E series, Руководство пользователя и инструкция по установке

Результаты поиска

Содержание DP2K-E series

Отзывы:

Похожие инструкции для DP2K-E series

Бренды по названию

Популярные бренды