Barco DP2K-36BLP, Руководство пользователя и инструкция по установке

Страница: 12 / 185

1. Safety
To prevent personal injury
• To prevent injury and physical damage, always read this manual and all labels on the system before powering the projector or
adjusting the projector.
• Do not underestimate the weight of the projector. The projector without the top cooler weighs ±106 kg ( ±233.7 lbs). To prevent
personal injury a hoisting tool should be used to lift the projector.
• To prevent injury, ensure that the lens, cooling system and all cover plates are correctly installed. See installation procedures.
• Warning: high intensity light beam. NEVER look into the lens ! High luminance could result in damage to the eye.
• Warning: extremely high brightness projector : This projector embeds extremely high brightness (radiance) lasers; this laser
light is processed through the projectors optical path. Native laser light is not accessible by the end user in any use case. The
light exiting the projection lens has been defused within the optical path, representing a larger source and lower radiance value
than native laser light. Nevertheless the projected light represents a signi
fi cant risk for the human eye when exposed directly
within the beam. This risk is not speci fi c related to the characteristics of laser light but solely to the high thermal induced energy
of the light source; which is equivalent with lamp based systems.
Thermal retinal eye injury is possible when exposed within the Hazard Distance. The Hazard Distance (HD) is de
fi ned from
the projection lens surface towards the position of the projected beam where the irradiance equals the maximum permissible
exposure as described in the chapter "High Brightness precautions: Hazard Distance (HD)", page 11.
• Based on international requirements, no person in allowed to enter the projected beam within the zone between the projection
lens and the related Hazard Distance (HD). This shall be physically impossible by creating suf
fi cient separation height or by
placing optional barriers. Within the restricted area operator training is considered suf fi cient. The applicable separation heights
are discussed in "High Brightness precautions: Hazard Distance (HD)", page 11.
• The projector shall be installed in a restricted access room equipped with a key or security lock preventing untrained persons
entering the Risk Group 3 use zone.
• Switch off the projector before attempting to remove any of the projector’s covers.
• When required to remove all power from the projector (eg during service), always disconnect the power from the projector
mains terminals and UPS INLET connector. Use the disconnect device in the building installation to disconnect the power to
the projector mains terminals, and unplug the power cord at the UPS INLET connector if the UPS INLET is separately powered.
• Do not place this equipment on an unstable cart, stand, or table. The product may fall, causing serious damage to it and
possible injury to the user.
• Lenses, shields or screens shall be changed if they have become visibly damaged to such an extent that their effectiveness is
impaired. For example by cracks or deep scratches.
• The associated Safety responsible of the unit must evaluate the setup before the unit may be started.
• Never point or allow light to be directed on people or re fl ective objects within the HD zone.
• All operators shall have received adequate training and be aware of the potential hazards.
• Strictly minimize the number of people who have access to the unit. The unit may never be operated without permission of the
responsible for safety.
• Do not put your hand or any body part in front of the beam.
Do not clean the port window when the projector is switched on.
• For a stand alone cooler, position the tubes so that they will not be tripped over, pulled, or contact hot surfaces.
To prevent fi re hazard
• Do not place fl ammable or combustible materials near the projector!
• Barco large screen projection products are designed and manufactured to meet the most stringent safety regulations. This
projector radiates heat on its external surfaces and from ventilation ducts during normal operation, which is both normal and
safe. Exposing
fl ammable or combustible materials into close proximity of this projector could result in the spontaneous ignition
of that material, resulting in a fi re. For this reason, it is absolutely necessary to leave an “exclusion zone” around all external
surfaces of the projector whereby no fl ammable or combustible materials are present. The exclusion zone must be not less
than 40 cm (16”) for this projector.
• Do not place any object in the projection light path at close distance to the projection lens output. The concentrated light at the
projection lens output may result in damage,
fi re or burn injuries.
• Ensure that the projector is solidly mounted so that the projection light path cannot be changed by accident.
• Do not cover the projector or the lens with any material while the projector is in operation. . Mount the projector in a well
ventilated area away from sources of ignition and out of direct sun light. Never expose the projector to rain or moisture. In
the event of
fi re, use sand, CO
2
or dry powder fi re extinguishers. Never use water on an electrical fi re. Always have service
performed on this projector by authorized Barco service personnel. Always insist on genuine Barco replacement parts. Never
use non-Barco replacement parts as they may degrade the safety of this projector.
• Slots and openings in this equipment are provided for ventilation. To ensure reliable operation of the projector and to protect
it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the
projector too close to walls, or other similar surface. This projector should never be placed near or over a radiator or heat
register. This projector should not be placed in a built-in installation or enclosure unless proper ventilation is provided.
• Projection rooms must be well ventilated or cooled in order to avoid build up of heat. It is necessary to vent hot exhaust air from
projector and cooling system to the outside of the building.
• Let the projector cool completely before storing. Remove cord from the projector when storing.
8 R5906753 DPXK BLP SERIES 20/11/2017