4. Troubleshooting
Code 5964: “light pipe - temperature sensor open” (Error)
Situation
Solution
Wire unit (reference 1image 4-42)
of the temperature sensor is
disconnected from the Signal
Backplane.
Plug in the wire unit of the temperature sensor into its socket on the Signal Backplane.
Damaged wire unit of the
temperature sensor which measures
the temperature of the cooling block
of the light pipe entrance.
1.
Repair the wire unit.
2.
If not repairable, replace the whole wire unit and temperature sensor.
Defect temperature sensor on
the cooling block of the light pipe
entrance.
Replace the temperature sensor.
1
Image 4-42
Light pipe temperature sensor connection
Code 5965: “light pipe - temperature sensor short” (Error)
Situation
Solution
Damaged insulation of the wire unit
of the temperature sensor (reference
1 image 4-42) which measures the
temperature of thecooling block
of the light pipe entrance. When
disconnecting the wire unit of the
temperature sensor from the Signal
backplane, the error code is changed
to “light pipe - temperature sensor
open 5964”.
1.
Repair the insulation of the wire unit using shrink sleeve.
2.
If not repairable, replace the whole wire unit and temperature sensor.
Defect temperature sensor on
the cooling block of the light pipe
entrance. When disconnecting the
wire unit (reference 1 image 4-42)
of the temperature sensor from the
Signal backplane, the error code is
changed to “light pipe - temperature
sensor open 5964”.
Replace the temperature sensor.
Code 6050: “dmd - temperature hardware protection warning” (Warning)
Situation
Solution
DMD temperature low.
Make sure that the ambient temperature is within specs. Let the projector acclimate to
the normal room temperature which should be higher then 10°C (50°F) and lower then
35°C (95°F). Do not ignite the lamp, otherwise there is a risk for condensate.
DMD temperature high.
Check all cooling systems: Air extraction system, dust
fi
lters, ...
70
R5905043 DP2K-12C/11CX 19/02/2018
Содержание DP2K-12C
