Barco DP2K-12C Скачать руководство пользователя страница 85

Страница: 85 / 111

11. Maintenance

11. MAINTENANCE

About this chapter

This chapter describes how to remove the dust

lters

Overview

•

Removing the front dust

lter

•

Clean the dust

lter on the bottom side

•

Clean the dust

lter on the top side

•

Cleaning the lens

•

Cleaning the exterior of the projector

•

Check cooling liquid level

•

Cleaning the UV blocker of the Lamp House

•

Authorization to clear security warning on the projector

The air

lters should be cleaned monthly under normal environment conditions. Equipment in very dusty or

otherwise contaminated areas may require more frequent maintenance.

If the air

lters are not regularly cleaned, the air

ow inside the projector could be disrupted and cause over-

heating. Overheating may lead to the projector shutting down during operation.

11.1 Removing the front dust

lter

The front

lter of the projector can be removed from the lamp side.

The

lter can be cleaned.

Remove the dust

lter

1. Remove the input cover of the projector, "Removal of the input cover", page 68.

2. Release the captive screw of the front cover.

Pull the left side of the front cover 5 centimeters forwards. There is no need to remove the cover completely.

R5905050 DP2K C-SERIES 10/07/2012

Содержание DP2K-12C
















































































































Результаты поиска

Содержание DP2K-12C

Отзывы:

Бренды по названию

Популярные бренды

Barco DP2K-12C, Руководство по установке

Результаты поиска

Содержание DP2K-12C

Отзывы:

Бренды по названию

Популярные бренды