Barco DP2K-12C Скачать руководство пользователя страница 83

Страница: 83 / 111

10. Removal and installation of projector covers

Necessary tools

Flat screw driver.

How to install the front cover of the projector?

1. Check if the front

lter is present.

2. Ensure that no lens is mounted and that the input cover is not installed.

3. Install the front cover of the projector doing the following:

rst hook in the side of the front cover at the front

lter,

b) then gently push the other side of the front cover into position,
c) ensure that the locking studs in the corners click into their receivers.

Image 10-23
Install front cover

4. Secure the front cover by locking the captive screw in the middle at the bottom of the front cover.

Image 10-24
Fasten front cover

5. Reinstall the rubber dust ring around the lens holder. See detail at the right of image 10-24.

10.13 Installation of the input cover

Necessary tools

Flat screw driver.

How to install the input cover of the projector?

1. Install the input cover of the projector doing the following:

a) Bring the input cover towards its

nal position (A),

b) then gently push the locking stud at the right top corner (B) into its receiver,
c) then gently push the locking stud at the right bottom corner (C) into its receiver.

R5905050 DP2K C-SERIES 10/07/2012

Содержание DP2K-12C
















































































































Результаты поиска

Содержание DP2K-12C

Отзывы:

Бренды по названию

Популярные бренды

Barco DP2K-12C, Руководство по установке

Результаты поиска

Содержание DP2K-12C

Отзывы:

Бренды по названию

Популярные бренды