Barco DP K-32B Series, Руководство пользователя и инструкция по установке

Страница: 21 / 190

R5905754 /13 DPxK-32B 21
2. Physical installation of the projector upon its pedestal and connecting the air outlet of the projector with the
exhaust system. Note that the exhaust system is MANDATORY. See chapters “ Positioning the DPxK-32B at
port window ” , page 24, and “ Installation of the exhaust system ” , page 26.
3. Power input set up and Electrical connection with the power net . See chapter “ Power input setup of the
DPxK-32B ” , page 29 and “ Connecting the DPxK-32B with the power net ” , page 30.
4. Installation of a suitable UPS unit or bypass the power in and outlet for the projector electronics. See
chapters “ Power loop through to the projector electronics ” , page 32 or “ Connecting a UPS to the projector
electronics ” , page 33.
5. Installation of the xenon lamp in case the xenon lamp is not installed in the lamp house yet. To install the
xenon lamp the lamp house has to be removed from the projector. To install the xenon lamp correctly and in a
safe manner, see the detailed step by step procedures in the chapter
“ Lamp & Lamp House ” , page 35.
6. Installation of the lens . First select an appropriate lens which throw ratio covers the screen size and the
projector - screen distance. Then install the lens in the lens holder of the projector. For more information about
available lenses, lens selection and lens installation see chapter
“ Lens installation ” , page 61.
7. Installation of the Communicator Touch Panel . See chapter “ Communicator Touch Panel ” , page 123.
8. Installation of the HDDs. In case the HDDs of the ICMP are delivered separated from the projector remove
the protection tape from the HDD input slots and install all three HDDs as described in the procedure
“ Installing a HDD into the ICMP ” , page 121. Make sure that all HDDs in the ICMP HDD set have the same
storage capacity. See label on top of the HDD to know the storage capacity.
9. Alignment of the projected image on the screen . The projector can now be switched on to project its first
image (test pattern) on the screen. Then the image can be aligned with the screen size of the application.
Follow the next steps to achieve that:
1. Place the ON/OFF switch of the projector in the ” I ” position. As a result the projector starts to initialize. The
status lights of the projector lights up GREEN once the projector is initialized.
2. Press the STANDBY button on the local keypad to activate the lamp.
3. Press the DOWSER button on the local keypad to open the dowser of the projector. The dowser is open if
the color of the DOWSER button is GREEN.
4. Press the TEST PATTERN button on the local keypad to project one of the internal test patterns of the
projector on the screen.
5. Use the lens ZOOM , SHIFT and FOCUS buttons on the local keypad the match the projected image with
the screen. Tilt the projector in case you can not SHIFT the image completely upon the screen. See “ Lens
shift, zoom & focus ” , page 65.
10. Resetting the lamp parameters . The “ LAMP INFO ” parameters which are stored on the controller board of
the projector MUST be updated after each installation of an xenon lamp inside the lamp house. Neglecting this
update will result in poor performance and short life time of the xenon lamp. See chapter
“ Resetting the lamp
parameters ” , page 53.
11. Realignment of the xenon lamp in its reflector . For optimal performance of the xenon lamp it is required to
realign the lamp after installation in the lamp house. See “ Realignment of the lamp in its reflector (manual
Lamp House) ” , page 56 for more information.
12. Adjusting the light path . Normally the lens holder and the convergence of the projector is perfectly adjusted
at the factory. Nevertheless, some applications require a readjustment of the lens holder, convergence or
both. See procedure
“ Scheimpflug adjustment ” , page 71, to adjust the Scheimpflug and see chapter
“ Convergence ” , page 155 to adjust the convergence of the light path.
13. SCC calibration .
Note: A Spatial Color Calibration (SCC) has to be execute in case of a first install or in case a High
Brightness lens is swapped with a High Contrast lens or vice versa. See user guide of the
Communicator for detail SCC calibration instructions.
14. Registration of the projector . The DPxK-32B is DCI compliant and should be registered by Barco.
Therefore, the digital certificate inside the projector will be used to secure encryption key communication
between the projector and the rest of the theatre system (server and theatre management system).
15. Projection of a digital cinema movie .
16. In case the projector is equipped with an ICMP, download the ICMP device certificate, request KDM and DCP
from your content supplier, ingest KDM and DCP, and play out the movie. for detailed instructions see chapter
“ ICMP ” , page 95, and user guide of the Communicator and/or (Web) Commander.
General