Barco DP-1200 Скачать руководство пользователя страница 70 | Manualshive

Страница: 70 / 134

background image

7. Communicator touch panel

7.1

Introduction

Communicator Touch Panel for digital cinema projectors

The Communicator Touch Panel is designed for multi-user command and control, the Communicator enables users to learn quickly
and operate ef

fi

ciently - using an elegant and

fl

exible touch panel interface. The interface’s commonality means that operators

can intuitively use any model in the product line, without restriction, and its user-friendly nature translates directly into a short and
enjoyable learning curve.

Image 7-1

Flexible touch panel interface

The touch panel interface can be mounted upon a swivel arm which easily

fi

ts on top of the DP-1200 projector. One central locking

mechanism of the swivel arm allows an instant

fi

xation of the touch panel interface in any position.

The touch panel interface can also be installed further away from the DP-1200 projector. For that you can use a serial (RS232) cable
up to 10 meter or an Ethernet cable up to 50 meter to realize a direct data communication between the DP-1200 projector and the
Communicator Touch Panel.

The touch panel interface can also be connected with a Local Area Network (LAN) just like the DP-1200 projector. In this case both
devices can communicate with each other as well.

The touch panel interface requires a voltage 12 VDC and 1,5 ampere. Note that the DP-1200 projector has a 12 VDC
output which can be used to power up the touch panel interface. Nevertheless, the use of a se12 VDC adaptor (1,5 ampere
minimum) is required in case the touch panel interface is installed more then a few meters away from the DP-1200 projector.

A crossed DC cable has to be used when connecting the +12 VDC output from the Input & Communication
unit of the DP-1200 projector directly with the Touch Panel interface.

Parts location of the touch panel interface

E

B

C

D

A

F

G

H

Image 7-2

A

Touch screen.

B

Communication ports.

C Knob to operate central swivel clamp.
D Base of swivel arm.
E

Power input (12 VDC – 1,5 A).

F

RS323 port (9 pins SUB-D ).

G Ethernet port (RJ45).

66

R59770242 DP-1200 06/01/2009

«
...
68
69
70
71
72
...
»

Содержание DP-1200







































































































































Отзывы:

Нет отзывов

Похожие инструкции для DP-1200

Бренд: Canon Страницы: 116

Бренд: Panasonic Страницы: 132

PTL711XU - LCD PROJECTOR

Бренд: Panasonic Страницы: 38

Бренд: InFocus Страницы: 2

Crouse-Hinds SD Series

Бренд: Eaton Страницы: 12

Бренд: Optoma Страницы: 67

Бренд: Wize Страницы: 2

E-VISION 4500 series

Бренд: Digital Projection Страницы: 30

Бренд: Barco Страницы: 111

Бренд: Rompa Страницы: 4

Бренд: Light Sky Страницы: 19

Бренд: Wolf cinema Страницы: 79

Бренд: Dukane Страницы: 4

Бренд: Dukane Страницы: 12

Бренд: Dukane Страницы: 9

Бренд: Brookstone Страницы: 24

Бренд: WowWee Страницы: 52

Бренд: STILFORD Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды