![background image](http://html1.mh-extra.com/html/barco/clm-hd8-r9050130/clm-hd8-r9050130_user-manual_4031414023.webp)
3. Physical installation
3. PHYSICAL INSTALLATION
About this chapter
This chapter explains how to install and set up your CLM projector. If you are familiar with the projector and want to quickly set it
up for temporary use, follow the “Quick setup” instructions below. For a more complete setup, follow the instructions and guides
covered in the remaining subsections.
Quick setup
The following steps describe briefly how to setup your CLM projector in a table mount front projection. Note that each step refers to
a corresponding procedure, which is more detailed and illustrated.
1.
Install the batteries of the remote control, see "RCU battery installation", page 20.
2.
Place the projector on a solid table in front of the screen at the expected throw distance. Ensure that the projector is installed
at right angles (horizontally and vertically) with the screen.
3.
Select and install an appropriate lens, which covers the throw ratio ( = screen size / projector screen distance). For more details
see "Lens selection", page 23, and "Lens formulas", page 24.
4.
Connect the projector with the local power net, see "Power connection", page 35.
5.
Connect your source to the appropriate input module, see "Input source connections", page 37.
6.
Switch ON the projector, see procedure "Switching on", page 45.
7.
Select the input slot at which your source is connected with. Do this by pressing the numeric key “1” or “2” on the remote control
unit or on the local keypad, see "Source selection", page 52.
8.
Zoom and shift the lens until the image is properly projected on the screen, Do this by using the “ZOOM” and “FOCUS” key on
the remote control unit or on the local keypad, see"Quick Lens Adjustment via LENS key", page 48 or "Direct Lens Adjustment
(RCU)", page 49. If necessary, level the projector from side to side by turning the adjustable feet in or out, see "Alignment of a
table mounted CLM projector", page 24.
Overview
•
•
•
Alignment of a table mounted CLM projector
•
Suspension of the CLM projector with rigging clamps
•
Alignment of a ceiling mounted CLM projector
3.1
Remote control unit (RCU)
Introduction
The standard remote control unit (A) can be equipped with the optional rugged case (B) and an XLR adapter (C).
The remote control unit can be used wired via mini-jack or via optional rugged XLR. Note that the backlight of the remote control unit
illuminate continuously when used with a wire.
C
B
A
Image 3-1
R59770057 CLM HD8 16/07/2007
19
Содержание CLM HD8 R9050130
