manualshive.com logo in svg

Barco BarcoData 2100 LC, Руководство по установке

Поделиться
Скачать
Barco BarcoData 2100 LC Скачать руководство пользователя страница 8

3-1

Off-axis Projection

5975349A RETRO BLOCK DATA 2100LC 200598

3

OFF-AXIS PROJECTION

Off-axis projection

The projector can be adapted to off-axis installation in order to meet

environmental conditions.  The range within which the projection

angle can be changed is 0° (= on-axis) to 10° downwards for the

QSD(0.8:1) and QSD(1.2:1) lens.

For every possible installation a number of things have to be geared

for one another:

- chosen lens : QSD(0.8:1) or QSD(1.2:1)

- position of the lens mounting, called 'discrete off-axis'

-  internal conversion-kit: for each projection-angle/lens combi-

nation a different fresnel-lens is needed (see Table 1)

- mechanical shift

Table 1

5HDU7DEOH

3URMHFWLRQDQJOH

 * Note: 

These combinations are not recommended!  The optical

performance towards the corners of the image is reduced.

Adjustment Procedure

Note:  for servicing the projector a special tool kit is available with the

Order No R9829530.

a) Changing the discrete off-axis

The discrete off-axis is determined by the position of the fixing

screws in the adaptation holes of the lens mounting.  On the lens

mounting, each of the  holes of the upper-right set have the

corresponding projection-angle/lens combinations indicated.

3URMHFWLRQDQJOH

/HQV46'

/HQV46'

ƒ

5.

5.

ƒ

5.

5.

ƒ

5.

5.

ƒ

5.

5.

ƒ

5.

5.

Содержание BarcoData 2100 LC












Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды