background image

21

USE  AND  CARE  INSTRUCTIONS

  WARNING

!

!

This  appliance,  when  installed,  must  be
electrically  grounded  in  accordance  with
local  codes  or,  in  the  absence  of  local
codes,  with  the 

National  Electrical  Code,

ANSI/NFPA 70, 

or the

 Canadian Electrical

Code,  CSA  C22.1.

Keep any electrical supply cord and the fuel
supply hose away from any heated surface.

To protect against shock hazard risk, connect  only
 to properly Grounded Outlet.

  CAUTION

!

!

To protect against electrical shock, do not immerse
electrical cord or plugs in water or expose to rain.
Protect electrical elements from burners, hot grill sur-
faces and grease.

  WARNING

!

!

CORRECT  USE  OF ELECTRICAL  EQUIPMENT

To protect against electric shock, do not immerse cord
or plugs in water or other liquid.

Allow Grill to cool before putting on or taking off parts.

Do not operate any outdoor cooking gas appliance with a
damaged cord, plug, or after the appliance malfunctions
or has been damaged in any manner. Call 1-877-934-

7455 for repair.

Do not let the cord hang over the edge of a table or touch

hot surfaces.

Do not use  an outdoor cooking gas  appliance for any

purposes other than its intended use.

When connecting, first connect plug to the outdoor cook-

ing gas appliance then plug appliance into the outlet.

Use only a Ground Fault Interrupter (GFI) protected cir-

cuit with this outdoor cooking gas appliance.

Never remove the grounding plug or use with an adapter

of 2 prongs.

Use only extension cords with a 3 prong grounding plug,

rated for the power of the equipment, and approved for
outdoor use with a W-A marking.

1.

2.

3.

CORRECT USE OF TRANSFORMER AND LIGHT

Read all instructions before initial use.

IMPORTANT: When using transformer appliances, basic

safety precautions should always be used.

The Transformer is set  for 120V, 60Hz, 28W, AC input  and

12V, 1800mA, 22W, AC output . The Light is set for 12V, 10W.

Do not  let children  operate or play  nearby  your  grill  or

Transformer. Always supervise children and pets if they are
in the vicinity of the unit.

Connecting Transformer

Always attach the assembled Transformer to your grill first

and then plug the Cord into a properly grounded outlet, then
turn on the Lights.

Operating Transformer and Light

Do not operate the Transformer if the cord or plug becomes

damaged, or if the Transformer or Light malfunctions or
have been damaged in any manner.

Do not immerse Electrical Cord or Plug in water or expose
to rain, as this may result in an electrical shock.

Disconnect Transformer

Be careful as all surfaces will be hot; including the grill,

Transformer, and the Light. Turn off the Lights and unplug
the Transformer from the electrical outlet when not in use
and before cleaning.

4.

9.

8.

7.

6.

5.

  WARNING

!

!

California Proposition 65
The electrical supply cord and plug of the Trans-
former  contain chemicals, including lead, known
to  the  State  of  California  to  cause cancer,  and
birth  defects  or  other  reproductive  harm.  Wash
hands after handling.

Содержание Turbo BTH2616ALP































Отзывы: