!
Error Messages
Battery check program
‘UNBALANCED’ - There are voltage difference more than 0.05V between the highest and lowest voltages of individual cells.
‘HIGH VOL’ - The voltage of any peculiar cell is higher than the safe value - LiPo: 4.24V, LiFe: 3.65V and LiIo: 4.14V.
‘LOW VOL’ - The voltage of any peculiar cell is lower than the minimum safe value - LiPo: 3.00V, LiFe: 2.50V and LiIo: 3.00V.
Self-balance mode
‘CELL LOW VOL’ - The voltage of cell is too low.
’CELL HIGH VOL’ - The voltage of cell is too high.
‘CELL CONNECT’ - There are bad connections on cable or connectors.
Warranty and service
We warrant this product for a period of
one year (12 months)
from the date of purchase. The guarantee applies only to such material or
operational defects, which are present at the time of purchasing the product. During that period, we will repair or replace without service
charge any product deemed defective due to those causes. You will be required to present proof of purchase (invoice or receipt). This
warranty does not cover the damage due to wear, overloading, incompetent handling or using of incorrect accessories.
+
-
+
-
+
-
+
-
+
-
+
-
Date of purchase :
Dealer :
Watt meter program
This program can measure the electric current on your power system.
You can drive the ESC without radio and receiver, using integrated signal generator. See the diagram
for battery connection.
-. Select the ‘Watt’ program by pressing ‘SELECT’ button.
-. And press ‘ENTER’ to start to measure.
-. The signal value always starts at its lowest value(899us). Use and button, to control the
speed of motor.
Watt LiPo
LiFe LiIo
◀
◀
‘ENTER’
WAT 12.6A 11.81V
148.2W 12.110AH
‘ESC’
As you start to run the motor, it shows the power consumptions in real time. They are current,
input voltage, wattage and current.
When you enter the watt-meter mode, you can calibrate all values to zero by pressing
‘SELECT’ and ‘ENTER’ buttons together for more than 3 seconds.
Speed
Controller
MOTOR
+
-
Beware of rotating propeller,
when you check the motor with
propeller. For maximum safety, hold
the motor on a test bench tightly,
and wear a safety eye protection
and hand gloves.
!
!
BANTAM Inc.
#623 Unitech Ville 1141-2
BAEKSEOKDONG ILSANDONGGU
GOYANGSI KYUNGGIDO
KOREA 410-722
Phone: +82 31 904 3939
Fax: +82 31 901 6439
E-mail: [email protected]
Web: www.bantamtek.com
S
+
-
S
+
-
+
-
Battery pack
(Power)
◀
◀
Servo test program
This program can drive any type of R/C servo to test without radio and receiver using integrated signal generator.
A battery pack of 4.8V is necessary using Y-harness cord to drive the servo and a battery pack of above 7.2V is also necessary to power the
TWO-METER itself.
-. Select the ‘Watt’ program by pressing ‘SELECT’ button.
-. And press ‘ENTER’ to start.
-. The signal value always starts at its lowest value(899us). Use and button, to drive the servo.
Watt LiPo
LiFe LiIo
◀
◀
‘ENTER’
WAT 0.0A 7.8V
0.0W 899uS
‘ESC’
S
+
-
+
-
Battery pack
(4.8V)
◀
◀
+
-
Battery pack
(> 7.2V)