e
STATION
-
!
!
- End curr. (End current) :
Set the final charging current at
termination.
Auto; The process will be terminated when the charging current
go to 1/10 of its initial value. Otherwise, the charge current will be
decreased until the input value has been reached. (Auto,
60~500mA)
- Tickle curr. (Trickle charge current) :
Activate or deactivate the
trickle charge after the termination of process. (Off, 50 ~ 300mA)
▶
▶
E n d c u r r : A u t o
M a x c a p a : 1 0 0 %
S a f e t y t i m e r : 7 2 0 m i n
S a f e t y t e m p : 5 0 C
Tr i c k l e c u r r : 1 0 0 m A
P b [ 1 ] 6 S ( 1 2 . 0 V )
1 2 0 0 0 m A h
C H A R G E
P b [ 1 ] 6 S ( 1 2 . 0 V )
1 2 0 0 0 m A h
C H A R G E
- 18 -
Using both OUTPUT-1 and OUTPUT-2
To activate opposite output channel during the process is running on an output, just press
‘CHANNEL’ button. The main menu screen or the program set-up screen will be shown for new
output. Even the screen switch to new display, the process keeps on running at the other
output. Connect the battery to new output channel, and select or set up suitable program by
following the instruction. After finishing the setup, press ‘START/ENTER’ button for more than
3 seconds to start the process at the output channel. Now, both output channels are running
their own process.
Remember both output channels have the circuit which is independent, but identical.
!
!
Discharging Pb battery
▶
D c h g c u r r : 5 . 0 A
D c h g v o l t : D e f a u l t
D c h g m o d e : N o r m a l
E n d c u r r : N o t u s e
M a x c a p a : 1 0 0 %
▶
D c h g m o d e : N o r m a l
E n d c u r r : A u t o
M a x c a p a : 1 0 0 %
S a f e t y t i m e r : 7 2 0 m i n
S a f e t y t e m p : 5 0 C
- Dchg. curr. (Discharge ent) :
Set the discharge current. (0.1 ~ 5.0A)
- Dchg. Volt (Discharge volt) :
Set the final voltage per cell. The final voltage should not be under the
voltage level that is recommended by the battery manufacturer to avoid deep discharging. (Default,
1.40~1.80V/cell)
- Dchg. mode (Discharge mode) :
Set the discharge mode.
Normal; The charger will keep on discharging with the discharge current continuously until the discharge
voltage has been reached.
CV mode; The discharging current will start to be decreased gradually until the end current which will
be set up at next has been reached, when the voltage has been dropped to the final discharge voltage.
- End curr. (End current) :
Set the final discharging current at termination.
The end current should be
less than the initial discharge current.
Auto; The process will be terminated when the discharge current go to 1/10 of its initial value.
Otherwise, the discharge current will be decreased until the designated value has been reached. (Auto,
60~500mA)
P b [ 1 ] 6 S ( 1 2 . 0 V )
1 2 0 0 0 m A h
DISCHARGE
P b [ 1 ] 6 S ( 1 2 . 0 V )
1 2 0 0 0 m A h
DISCHARGE
C h g c u r r : 5 . 0 A
C h g v o l t : D e f a u l t
C h g m o d e : L i n e a r
E n d c u r r : A u t o
M a x c a p a : 1 0 0 %
!
