SureCross Performance Node
P/N 158215-KR
Rev. C
www.bannerengineering.co.kr
3
Switches
Device Settings
1
2
3
4
5
6
7
8
DIP switch configured (Uses 5-8 for I/O configuration)
ON
12 inputs, 0 outputs
OFF*
OFF*
OFF*
OFF*
11 inputs, 1 output
OFF
OFF
OFF
ON
10 inputs, 2 outputs
OFF
OFF
ON
OFF
9 inputs, 3 outputs
OFF
OFF
ON
ON
8 inputs, 4 outputs
OFF
ON
OFF
OFF
7 inputs, 5 outputs
OFF
ON
OFF
ON
6 inputs, 6 outputs
OFF
ON
ON
OFF
5 inputs, 7 outputs
OFF
ON
ON
ON
4 inputs, 8 outputs
ON
OFF
OFF
OFF
3 inputs, 9 outputs
ON
OFF
OFF
ON
2 inputs, 10 outputs
ON
OFF
ON
OFF
1 input, 11 outputs
ON
OFF
ON
ON
0 inputs, 12 outputs
ON
ON
OFF
OFF
6 inputs, 6 outputs (non bit-packed)
ON
ON
OFF
ON
8 bit-packed inputs, 4 non bit-packed outputs
ON
ON
ON
OFF
4 non bit-packed inputs, 8 bit-packed outputs
ON
ON
ON
ON
* Default configuration
For the 6 IN/6 OUT non bit-packed configuration, the discrete INs use I/O points 1 through 6 and the discrete OUTs use I/O points 9
through 14. For the 8 bit-packed IN/4 non bit-packed OUT configuration, all discrete INs use I/O point 1 and the discrete OUTs use I/O
points 9 through 12. For the 4 non bit-packed IN/8 bit-packed output configuration, the discrete INs use I/O points 1 through 4 and all bit-
packed outputs use I/O point 9.
Modbus/UCT Configured or DIP Switch Configured for I/O Configuration
In the OFF position, this device is configured for six discrete inputs and six discrete outputs (non-bit packed) for products built after May
2011. For products built before May 2011, this default position configures the device for 12 inputs and zero outputs (bit packed). In the
OFF position, users can send commands directly from the host system to the devices to select custom I/O configuration. Users may also
use the User Configuration Tool (UCT) to write custom configuration
In the ON position, use DIP switches 5 through 8 to select one of the pre-programmed discrete I/O configurations shown in the DIP
Switch Settings table.
Transmit Power Levels
The 900 MHz radios can be operated at 1 watt (30 dBm) or 250 mW (24 dBm). While the radios operate in 1 Watt mode, they cannot
communicate with 150 mW DX80 radio devices. To communicate with the 150 mW radio models, operate this radio in 250 mW mode.
For 2.4 GHz radios, this DIP switch is disabled. The transmit power for 2.4 GHz is fixed at about 100 mW EIRP (18 dBm), making the 2.4
GHz Performance models automatically compatible with the DX80 2.4 GHz models.
User Defined Configuration of Discrete I/O on the 12 I/O Devices
The 12 I/O device can be configured into any combination of 12 discrete inputs or outputs. Inputs are stored in a bit packed form in I/O
point 1, device register 1. Outputs are stored in a bit packed form in I/O point 9, device register 9. (See Modbus Register Block table on
previous page.)
Defining Inputs and Outputs
To define which of the 12 I/O points are inputs, adjust the bit field stored as I/O 1’s threshold parameter [15:0]. Set bit 0 of the 16-bit
parameter data word to define I/O 1 as an input, set bit 1 to define I/O 2 as an input, et cetera. Each bit position of the parameter is
associated to a I/O point. In the example below, the first five I/O points are defined as inputs.
