Banner Sure Cross DXM100-Bx Скачать руководство пользователя страница 6

Страница: 6 / 82

User Interface—A simple user interface consists of an LCD screen and four LED indicators. Use the LCD to access system

status and setup, view user selectable events or data, and to bind and perform site surveys for Sure Cross radios.

Configure the user programmable LEDs to indicate the status of the DXM Controller, processes, or equipment.

User programmable LCD

Bind Sure Cross Radios
Site Survey
View Sensor Information
System Status

User Defined LED indicators

1.2 DXM Automation Protocols

The DXM Controller supports the following automation protocols.

Modbus RTU. The DXM Controller manages two separate physical ports running the Modbus RTU protocol. The DXM

Controller is the Modbus Master when operating the Modbus master RTU port. The DXM Controller uses the master Modbus

RTU bus to communicate with locally connected Modbus devices or uses the Banner wireless radio to communicate with

remote Modbus devices. The other Modbus RTU port is used by a host system to access the DXM Controller as a slave

device. The slave Modbus RTU port allows access all the internal registers concurrently with the master RTU port. By

default, the Modbus RTU ports are active. Configure the port parameters using the DXM Configuration Tool.

Modbus TCP/IP. A host system acting as a Modbus client can access the DXM Controller using the Modbus TCP/IP

protocol over Ethernet. Standard Modbus port 502 is used by the DXM Controller for all Modbus TCP/IP requests. All

internal registers are available to the host system concurrently with Modbus RTU. By default, Modbus TCP/IP is active.

EtherNet/IP

™

. The Ethernet port is actively running EtherNet/IP. From the factory the DXM Controller is configured to

read and write registers on DX80 wireless devices 1 through 16. Custom configurations can be set using the DXM

Configuration Tool. By default, EtherNet/IP is active.

1.3 DXM Modbus Overview

The DXM Controller uses internal 32-bit registers to store information. The processor's internal Local Registers serve as the

main global pool of registers and are used as the common data exchange mechanism. External Modbus device registers

can be read into the Local Registers or written from the local data registers.

The DXM Controller, as a Modbus master device or slave device, exchanges data using the Local Registers. Modbus over

Ethernet (Modbus/TCP) uses the Local Registers as the accessible register data.

Using Action, Read/Write, and Threshold Rules allows you to manipulate the processor's Local Registers. The ScriptBasic

programming capabilities extends the use of Local Registers with variables to create a flexible programming solution for

more complex applications.

The processor's Local Registers are divided into three different types: integer, floating point, and non-volatile. When using

Local Registers internally, the user can store 32-bit numbers. Using Local Registers with external Modbus devices follows

the Modbus standard of a 16-bit holding register. Local Registers are accessible as Modbus ID 199.

Accessing the I/O Base and the LCD follows the same communication as an external Modbus device. Each device has an ID

number to uniquely identify itself. The I/O base is Modbus ID 200 and the LCD is Modbus ID 201.

DXM100-Bx Wireless Controller Instruction Manual

www.bannerengineering.com - Tel: 763.544.3164

Содержание Sure Cross DXM100-Bx


















































































Результаты поиска

Содержание Sure Cross DXM100-Bx

Отзывы:

Banner Sure Cross DXM100-Bx, Инструкция по эксплуатации, Страница: 6 / 82

Результаты поиска

Содержание Sure Cross DXM100-Bx

Отзывы: