Banner SLLVE23-350 Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 76

background image

Standard Receivers (SLLR..-….P8)—Use with a CSB-M128..M1281 splitter cable and optional DEE2R-8..D double-ended cables. Use only
EZ-LIGHT models with the suffix "8PQ8" when connecting to the machine interface connection. See datasheet p/n

for more

information.

Models

Construction

Connector/LED Function/Inputs

M18RGX8PQ8 12

Nickel-plated brass housing, M18 × 1 thread; thermoplastic
lens

Fully encapsulated IP67

8-pin M12/Euro-style Integral QD
Red/green indication follows OSSD output

of the EZ-SCREEN receiver
Red ON: Power ON, Beam Blocked, or

Lockout
Green ON: Power ON or Beam Clear

T18RGX8PQ8

Thermoplastic polyester housing, thermoplastic lens

Fully encapsulated IP67

T30RGX8PQ8

K30LRGX8PQ8

Polycarbonate housing, 30 mm thermoplastic dome, 22 mm
base mount

Fully encapsulated, IP67

K50LRGX8PQ8

Polycarbonate housing, 50 mm thermoplastic dome, 30 mm
base mount

Fully encapsulated, IP67

K80LRGX8PQ8

Polycarbonate housing, 50 mm thermoplastic dome, flat or
DIN mount

Encapsulated electronics, IP67

11.13 MSM Series Corner Mirrors

• Compact for light-duty applications
• Rear-surface glass mirrors are rated at 85% efficiency. The total sensing range decreases by approximately 8% per

mirror. See mirror data sheet p/n 43685 or

http://www.bannerengineering.com

for further information.

• Mounting brackets may be inverted from the positions shown (flanges pointing "inward" instead of "outward," as

shown). When this is done, dimension L1 decreases by 57 mm.

• MSAMB adapter bracket kit included with each MSA stand.

12 Available in a kit that includes one M18 EZ-LIGHT, one SMB18A mounting bracket, and hardware for mounting to the side channel of an EZ-

SCREEN housing (kit model number EZA-M18RGX8PQ8).

EZ-SCREEN

®

LS Basic Safety Light Screen

www.bannerengineering.com - Tel: 763.544.3164

69

«
...
67
68
69
70
71
...
»

Содержание SLLVE23-350













































































Отзывы:

Нет отзывов

Похожие инструкции для SLLVE23-350

Split Vision VSLR3

Бренд: Federal Signal Corporation Страницы: 4

Бренд: OBSBOT Страницы: 4

Бренд: Z-Wave Страницы: 13

Бренд: hager Страницы: 2

Бренд: sewerin Страницы: 102

Бренд: Vicon Страницы: 28

Бренд: Aigis Mechtronics Страницы: 20

Бренд: wavestore Страницы: 15

Бренд: Velleman Страницы: 56

Бренд: jablotron Страницы: 2

Бренд: Baldwin Boxall Страницы: 7

Бренд: DSC Страницы: 8

Бренд: C&K systems Страницы: 2

Бренд: ESP Страницы: 55

Бренд: Lorex Страницы: 1

Бренд: Triplett Страницы: 44

Бренд: Raptor Страницы: 19

IPC-HFW3841E-AS-0280B-S2

Бренд: Dahua Technology Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды