Banner SLLVE23-350 Скачать руководство пользователя страница 75

Страница: 75 / 76

Part-Revolution Clutch

A type of clutch that may be engaged or disengaged

during the machine cycle. Part-revolution clutched

machines use a clutch/brake mechanism, which can

arrest machine motion at any point in the stroke or

cycle.

Pass-Through Hazard

A pass-through hazard is associated with

applications where personnel may pass through a

safeguard (which issues a stop command to remove

the hazard), and then continues into the guarded

area, such as in perimeter guarding. Subsequently,

their presence is no longer detected, and the related

danger becomes the unexpected start or restart of

the machine while personnel are within the guarded

area.

Point of Operation

The location of a machine where material or a

workpiece is positioned and a machine function is

performed upon it.

PSDI (Presence-Sensing Device Initiation)

An application in which a presence-sensing device is

used to actually start the cycle of a machine. In a

typical situation, an operator manually positions a

part in the machine for the operation. When the

operator moves out of the danger area, the presence

sensing device starts the machine (no start switch is

used). The machine cycle runs to completion, and

the operator can then insert a new part and start

another cycle. The presence sensing device

continually guards the machine. Single-break mode

is used when the part is automatically ejected after

the machine operation. Double-break mode is used

when the part is both inserted (to begin the

operation) and removed (after the operation) by the

operator. PSDI is commonly confused with "Trip

Initiate." PSDI is defined in OSHA CFR1910.217.

Banner safety light screen systems may not be used

as PSDI devices on mechanical power presses, per

OSHA regulation 29 CFR 1910.217.

Qualified Person

A person who, by possession of a recognized degree

or certificate of professional training, or who, by

extensive knowledge, training and experience, has

successfully demonstrated the ability to solve

problems relating to the subject matter and work.

Receiver

The light-receiving component of a safety light

screen system, consisting of a row of synchronized

phototransistors. The receiver, together with the

emitter (placed opposite), creates a "screen of light"

called the defined area.

Reset

The use of a manually operated switch to restore the

safety outputs to the On state from a lockout

condition.

Resolution

See

Minimum Object Sensitivity

EZ-SCREEN

LS Basic Safety Light Screen

www.bannerengineering.com - Tel: 763.544.3164

Содержание SLLVE23-350












































































Результаты поиска

Содержание SLLVE23-350

Отзывы:

Похожие инструкции для SLLVE23-350

Бренды по названию

Популярные бренды

Banner SLLVE23-350, Инструкция по эксплуатации

Результаты поиска

Содержание SLLVE23-350

Отзывы:

Похожие инструкции для SLLVE23-350

Бренды по названию

Популярные бренды