manualshive.com logo in svg

Banner DF-G3 Long Range Expert, Инструкция по эксплуатации, Страница: 19 / 36

Поделиться
Скачать
Banner DF-G3 Long Range Expert Скачать руководство пользователя страница 19

4. Exit Dynamic TEACH.

Method

Action

Result

SET 

Button

Click the SET rocker 

button

TEACH Accepted
Displays alternate "PASS" with % Minimum

Difference

10, Sensor returns to Adjust

mode

 

TEACH Not Accepted
Displays alternate "FAIL" with % Minimum

Difference

10, Sensor returns to Adjust

mode

 

Remote Input

Single-pulse remote input

T

5. Return to RUN Mode.

Method

Action

Result

SET 

Button

Move Mode switch to RUN

Display: Red - Signal Level; Green -

Threshold

Remote Input

No 

action

 required; sensor returns to RUN

mode 

automatically

3.5.3 Window SET

• Sets window thresholds that extend a programmable % 

offset

 above and below the presented 

condition

• All other 

conditions

 (lighter or darker) cause the output to change state

• Sensing window center can be adjusted using "+" and "-" rocker 

button

 (Manual Adjust)

• Recommended for 

applications

 where a product may not always appear in the same place, or when other signals may appear

• See Program Mode for programming the 

Offset

 Percent 

setting

A single sensing 

condition

 is presented, and the sensor 

positions

 window thresholds a programmable % 

offset

 above and below the

presented 

condition.

 In LO mode, Window SET designates a sensing window with the Output ON 

condition

 inside the window, and the

Output OFF 

conditions

 outside the window.

Sensor positions 
window thresholds 
a programmable %
offset from the 
presented condition

Darkest

(no signal)

Most Light

(saturated

signal)

Condition 

Presented

Sensing window

center adjusted by

Manual Adjust

Output OFF

Output OFF

Output ON

Figure 8. Window SET (Light Operate shown)

The Output ON and OFF 

conditions

 can be reversed by using the LO/DO (Light Operate/ Dark Operate) switch or through the program

interface for the dual output model.

Window SET and Manual Adjust 

Moves sensing window center value up or down to make adjustments

• Slide Mode switch to ADJ to enter Adjust mode

• Press "+" to increase; press "-" to decrease

◦

GREEN display shows the sensing window center value

◦

2 seconds 

after

 adjustment, the GREEN display will 

flash

 3 

times

 to 

confirm

• Slide Mode switch to RUN to complete 

operation

10 See 

Troubleshooting

 

on page 25 for more 

explanation

 of the % Minimum 

Difference

 displayed 

after

 the Dynamic TEACH method.

 

 

DF-G3 Long Range Expert

™

 Dual Display Fiber 

Amplifier

 

www.bannerengineering.com - Tel: 763.544.3164

19

Содержание DF-G3 Long Range Expert





































Отзывы:

Нет отзывов