B&Q plc, Chandlers Ford, Hampshire, SO53 3YX.
Visit us at
www.diy.com
Fit the Hinge Covers F306
over the Hinges.
Recycling – the packaging materials for this
product may be recycled through your local
recycling centre. When you want to dispose of
the product itself, please consider donating it
to a local charitable organisation, otherwise
recycle it through your local recycling centre.
F676
Recycling
–
the packaging materials for this product may be recycled through your local recycling centre. When you want to dispose of
the product itself, please consider donating it to a local charitable organisation. Otherwise, recycle it through your local recycling centre.
9
Fitting of Plinth
The plinth should be
cut to the required
length, allowing for
the mitre joint, and
then stuck onto the
unit, using a suitable
adhesive.
10
Fitting of Cornice
The cornice should be cut to the
required length, allowing for the
mitre and the overhang, and then
screwed into place using suitable
fixings (not supplied).
If space allows, screw into place
from above, through the 15mm
flat. If not, using a 5mm drill
bit, drill and countersink from
the underside of the top panel,
and fix in place. (And then fill
afterwards, if required).
Note:
Plinths and Cornices are supplied separately. If you
are in any doubt about fitting these items, you should
seek advice from an expert.
door Hinges
8
Handle Fixing
From the
rear face
of the Door, drill
through the holes using a 2.5mm
diameter drill.
From the
front face
of the Door,
open out the 2.5mm diameter holes
using a 5mm drill.
Screw Handles to Doors with the
Screws provided.
Insert the Hinges into the large
holes in the Doors and secure into
place using Screws .
Stick the Door Buffers onto
the bottom corners of the Doors
opposite to the Hinges.
before fitting the Hinges to your door you will have to drill the hole(s) required
through the appropriate pilot holes for the Handles you have purchased.
PILOT
HOLES
Q
Q
Q
S
S
S
S
C
Q
ensure your unit is level before you attempt to fit your doors.
Fit the Hinge Covers
over the Hinges.
K
Push hook on the Hinge Arm underneath the Hinge Plate.
Press front of Hinge Arm down onto Hinge Plate until it
‘clicks’ into place.
Before adjusting the Doors, use a spirit level to
check the Base (or Top) of the unit is level front-to-
back and side-to-side in the three positions shown.
Height:
Loosen screws ‘A’ on fixing
plates and move Door up or down as
required. Retighten screws ‘A’.
A
A
B
C
CLICK!
A
A
B
C
CLICK!
make the unit level beFORe making any adjustment to
the hinges as shown.
Forward or backwards:
Loosen
screw ‘B’ on fixing plate and move
Door in or out as required. Retighten
screw ‘B’.
Sideways:
To move Door ‘OUT’ at
hinge position, slacken screw ‘C’.
To move Door ‘IN’ at hinge position,
tighten screw ‘C’.
A
A
B
C
CLICK!
A
A
B
C
CLICK!
A
A
B
C
CLICK!
K
S
That’s the double Wardrobe completed.
Take care of your unit by using a damp cloth to clean it.
Soft Closer
11
The soft close mechanism , should be fitted onto one of the hinges, two per door, as shown,
(the mechanism simply clips into place over and into the hinge cup).
Adjustment of this device can then be made, by turning the dial at the bottom of the unit.
AT
AT
S
CSS1350 05/10
