Bandit INTIMIDATOR 18XP/1590 Скачать руководство пользователя страница 23

Страница: 23 / 185

Bandit

MODEL 18XP/1590

This chipper is designed to be “HAND FED” only!

DO NOT feed wood with any type of knuckle boom

loader, front end loader, or mechanical device. It will

cause damage to the machine. If this happens, the

machine WILL NOT be covered under warranty.

WARNING

SAFETY PROCEDURES

Before attempting any type of maintenance

disengage clutch, turn off engine, wait for the chipper

disc/drum to come to a complete stop, install the

disc/drum lock pin, disconnect battery, and make

sure the ignition key is in your possession.

ALWAYS install the disc/drum lock pin to prevent

inadvertent rotation. On disc chippers insert lock pin

through lock pin tube on the belly band under hood

rest. On drum chippers insert lock pin through lock

pin tube on side of drum housing.

Simply slide the lock pin into the disc/drum lock

tube. This is to ensure that the chipper disc/drum

cannot be started while you are working inside the

machine. If for some reason the chipper disc/drum

would start to turn, it would simply hit the lock pin.

DO NOT remove the hood pin until the chipper

disc/drum has came to a complete stop. The chipper

disc/drum will coast for several minutes after the

engine is shut down. Always wait at least several

minutes.

DO NOT operate this machine without the Hood

Pin in place. Do not operate the machine with any

type of makeshift hood pin or an improperly installed

hood pin! The Hood Pin MUST be padlocked.

DO NOT operate the machine with the chipper

hood open under any circumstances.

DO NOT operate this machine indoors! Exhaust

fumes can be fatal. Never refuel while the machine is

running. Never refuel in the shop or building. Always

refuel in a well ventilated area, away from sparks

or open fl ames, DO NOT SMOKE. Extinguish all

smoking materials. Wipe up all spilled fuel before

restarting the engine. Do not fi ll above 1/2” (12.7mm)

from top of tank for diesel engines and 2” (50mm)

from the top of the tank for gasoline engines.

To obtain the most from your machine, for the

least amount of cost, it is a good practice to set up

and follow a scheduled preventative maintenance

program. It will eliminate many possible problems

and down time.

DO NOT feed vines or vine-like material! DO NOT

pile vines or vine-like material in front of the infeed

hopper which may cause you to trip or fall! DO NOT

allow vines or limbs to become entangled with you or

your clothing! ALWAYS cut vine-like material into 4 to 5

foot (1.2 to 1.5 meter) length’s, away from the chipper

area! ALWAYS stop the feed system before feeding the

cut vine-like material into the infeed hopper! ALWAYS

use a wooden pusher paddle when feeding the cut

vines into the feedwheel(s)! ALWAYS be in position

and prepared to activate the feed control handle!

Never use jumper cables during freezing

temperatures. Tow the machine inside and allow

the battery time to warm up. If the machine must

be started outside, inspect the battery acid for ice

formation. Explosion will occur with a frozen battery.

If the machine is going to be operated in excessively

cold conditions, a larger cold cranking amp battery

may be needed to ensure proper and prompt

starting. Never use jumper cables in a confi ned or

unventilated area. Battery acid fumes are explosive.

Battery acid can cause severe burns. Never expose

an open fl ame or spark near the battery. Keep all

burning materials away from the battery. When

servicing the battery, shield eyes and face, and do

not smoke. Service in a well ventilated area.

Keep the machine in good condition. Be sure the

machine is in good operating condition and that all

safety devices, including guards and shields are

installed and functioning properly. Visually inspect

the machine daily before starting the machine. Refer

to the “Daily Start Up & Maintenance”. Make no

modifi cations to your equipment unless specifi cally

recommended or requested by Bandit Industries Inc.

Avoid moving parts. Keep hands, feet, and clothing

away from power driven parts. Keep all guards and

shields in place and properly secured.

Never feed any materials that might contain

wires, stones, nails, metal objects, or any foreign

object which may damage the knives and become

dangerous projectiles.

DANGER

WARNING

Chipper knives are sharp and can be dangerous.

It is always necessary for your protection to be

extra careful and wear proper hand protection when

handling knives.

The knives must be securely fastened and torqued

in position. If one comes loose or breaks during

operation, someone or something may get injured

or damaged.

DANGER

Содержание INTIMIDATOR 18XP/1590


























































































































































































Результаты поиска

Содержание INTIMIDATOR 18XP/1590

Отзывы:

Похожие инструкции для INTIMIDATOR 18XP/1590

Бренды по названию

Популярные бренды

Bandit INTIMIDATOR 18XP/1590, Инструкция по эксплуатации и каталог запасных частей

Результаты поиска

Содержание INTIMIDATOR 18XP/1590

Отзывы:

Похожие инструкции для INTIMIDATOR 18XP/1590

Бренды по названию

Популярные бренды