B&D The Designer Series, Руководство по установке

Страница: 7 / 22

2.0 assembly
2.1 vertical tracks
a) All the Vertical Straight tracks
D
are cut to length in factory.
Confirm the measurement matches calculation in 1.4.2.
b) Affix the small angle jamb brackets G and short top track
angle
E
to the straight track
D
using 6 x 1 /
4
flat head bolts
and wiz nuts, noting the distance required from the wall to
the track as shown in Fig 2.1.1. Further adjustment may be
required, depending on type of structure.
c) Connect the horizontal bracket F
to the short top track angle
E
using a
1 /
4
domed head bolts and wiz nut in top corner of
the “V”.
NOTE : The small angle jamb brackets and the short top track
D
E
G
Fig: 2.1.1
left hand track shown
2.2 bottom panel
a) Open up the pack of door panels, making sure the bottom panel (weather strip seal on the bottom of the panel
and bottom hinge hole) is on top of the pack. Start with the bottom panel.
NOTE:
Refer to appendix if installing a taper or rear torsion system as this requires a different hanger.
N
S
tip
Do not unwind lifting cable until specified
to do so.
b) For single end stile doors;
Place the axles plate
hanger R onto the bottom hanger S
and
secure onto the bottom panel as shown in Fig
2.2.1a using six (6) tek screws. NOTE: Bottom
panel bracket Y
needed only on some doors.
For double end stile large doors:
Place the bottom
HD hanger S
and secure onto the bottom panel as
shown in Fig 2.2.1 using nine (9) tek screws.
Fig: 2.2.1
F
70mm
40mm
H
T
R
M
M
P
Q
tip
Apply general purpose grease to all axles
before fitting them.
c) Slide the wheel axle
M
through the axle plate
hanger R Fig 2.2.1a or bottom HD hanger S
Fig 2.2.1.
angle, provide adjustable slots to move the track out from the wall. For larger doors over 2400mm high
one bracket is placed at the bottom and the second backet placed approximately midway.
d) For single end stile doors;
Push the end of each lifting
cable N , onto the bottom hanger, followed by a
washer
H
and secure with a snap pin
T
Fig 2.2.1a.
For double end stile large doors:
Push the end of
each lifting cable
N
, onto the panel side pin of the
bottom hanger and secure with a snap pin T
to the
outside of the pin in Fig 2.2.1.
e) To attach hinge
P
to the top of the panel, align the
edges of the hinge with the vertical grooves in every
door stile. Position the hinge as shown and affix with
(2) tek screws (Fig 2.2.1b).
Fig: 2.2.1a
Fig: 2.2.1b
Fig: 2.2.1c
Fig: 2.2.1d
S
N
T
oil hole to
the top
Ensuring the hinges are horizontally aligned across the panel will
provide a smoother door operation.
ii
W
M
f) Before placing 2 end hinges Q at either end of the panel, remove the 2 axle plates ii and screws from each hinge. Slide
in wheel axle M through the axle spacer W and onto the axle plates ii
for each end and put aside for later (Fig 2.2.1c).
g) The fixings must align with the vertical grooves in the stile then, secure both end hinges Q with eight (8) tek screws as
shown in Fig 2.2.1d. NOTE: Once the panel is in place the hinged hangers Q can be adjusted if needed to ensure the
panels are parallel to the opening.
Y
tip
7 The Designer Series & P7 Industrial ™ installation instructions