B&D Panelift B&D Storm-Shield PFI Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 32

background image

place the torsion bar on the floor and position the lifting parts
in order. place the spring anchor bracket onto the torsion bar,
positioning it approximately half way along.The cut off comer
should face the floor if mounted on the lintel, or if mounted on
the ceiling should face rearward, away from the lintel to allow
the panels to clear as the door operates, see Figure 37.

with single spring doors, slide a shaft collar against the spring
anchor bracket. The bearing flange in the spring anchor bracket
must face the spring. It may need to be reversed depending on
whether a left or right hand spring is supplied, see Figure 38.

The shaft collar is tightened against the bearing flange. Slide the
spring onto the torsion bar and over the shaft collar. A left hand
spring has a red winding plug, and should be fitted to the left
hand side of the spring anchor bracket. A right hand spring has
a black winding plug. The winding plugs should face away from
the spring anchor bracket, see Figure 39.

NOTE:

It is important to use 2 of the 4 1¼ inch square necked

bolts to secure each side bearing plates in position.

Refer to page 28 when adding spring tension.

Cable Drums

Red* & Black*

Spring

Axle

Shaft

Collar

Washer

Side Bearing

Brackets

Spring Anchor

Bracket 65mm

Shaft Collar to be butted up against

Anchor Bracket and fixed to axle

on spring side

of Anchor Bracket

DO NOT TIGHTEN

YET

FIGURE 38

FIGURE 39

Cable Drum marked

with Red Paint

Winding Plug marked

Refer to page 14

Cable Drum marked

with Black Paint

Bolt 3/8”

Nut 3/8”

Washer 3/8”

Shaft Collar

Note regarding Part Numbers

Springs and Cable Drums vary

from across different door sizes

FIGURE 37

Fixed to

Ceiling

Fixed to

Wall

Cut Corner facing down

FIGURE 2.11.1 PARTS NEEDED - SINGLE SPRINGS

2.11 STANDARD SPRING COUNTERBALANCE SYSTEM

21

panelift

®

pFT, panelift

®

Icon

™

pFI, b&D Storm-Shield

™

pFI and Insul-Shield

™

Installation Instructions

Revision 9 - March 2016

«
...
19
20
21
22
23
...
»

Содержание Panelift B&D Storm-Shield PFI

































Отзывы:

Нет отзывов

Похожие инструкции для Panelift B&D Storm-Shield PFI

Бренд: CAME Страницы: 40

Easy Touch 681131066235

Бренд: GE Страницы: 8

Бренд: Essmann Страницы: 10

ZEROQUATTRO 180

Бренд: O&O Страницы: 2

Бренд: FAAC Страницы: 32

Бренд: GDS Страницы: 15

Бренд: Seav Страницы: 76

Бренд: Key Automation Страницы: 14

DC BLUE ADVANCED

Бренд: E.T. Systems Страницы: 32

Бренд: E.T. Systems Страницы: 24

Бренд: tau Страницы: 68

Бренд: Chamberlain Страницы: 28

Бренд: Chamberlain Страницы: 44

Бренд: DITEC Страницы: 122

44 Double Flush

Бренд: Wayne-Dalton Страницы: 16

Бренд: Atecnica Страницы: 15

Бренд: DoorKing Страницы: 42

Бренд: B&D Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды