B&C LR3D-14 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 16

B&C LR3D-14 Скачать руководство пользователя страница 6

LR3D Technical Manual

Section A

Rev. IR (5/13/2020)

Introduction

B&C Specialty Products

Page A - 4

bandc.com

AR

M22759/16-18-9

Wire, 18 AWG, White, Tefzel

AR

M22759/16-22-9

Wire, 22 AWG, White, Tefzel

2 AN4-4A

Bolt

4 AN960-416L

Flat

washer

2 AN365-428A

Locking

nut

The above items are available individually, or as part of an installation kit (P/N: LR-INSTALL),
from B&C Specialty Products, bandc.com, phone: 316-283-8000.

CHANGE IN WEIGHT AND BALANCE

The LR3D Controller weighs a nominal 0.6 lbs. Variations in airframe station references for all
aircraft affected by this kit preclude including pre-calculated weight and balance data in this
manual. Weight of electrical accessories and hardware will vary for each individual installation.
The installer is responsible for ensuring that aircraft weight and balance are correct.

«
...
4
5
6
7
8
...
»

Содержание LR3D-14

















Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды