B&B 3PCIU2 Скачать руководство пользователя | Manualshive

Страница: 14 / 57

background image

Serial Card Setup

8

Chapter 2

Document Number 3PCI-0712m

multipoints) the transmitter can be enabled all the time. Placing the middle DIP switch in
the TX ON position accomplishes this.

For RS-485 operation the middle DIP switch is placed in the TX SD position. In this
position the transmitter is only enabled when data is being sent. The transmitter is tri-
stated when not sending data, allowing other transmitters on the communications line to
transmit without interference.

DIP Switch 3 (RS-232/422/485 ports)

The bottom DIP switch (3) configures the port for half-duplex (two-wire) RS-485
operation or full-duplex (four wire) RS-422/RS-485 operation. Placing the bottom DIP
switch in the RX ON position configures the port for four wire operation. In this mode the
receiver is continuously enabled, allowing it to receive all data on the communications
line. Since the transmitter sends data on the other wire pair the port does not receive its
own transmissions.

Placing the bottom DIP switch in the RX

position configures the port for two wire

operation. In this mode the transmitter and receiver are connected to the same wire
pair. The receiver is disabled when its transmitter is sending, preventing the port from
receiving its own data.

Setting the DIP Switches on RS-422/485 Only Ports

The 3PCIOU4 MIport card provides a combination of RS-232/422/485 and RS-422/485
only ports. Ports that do not include RS-232 operation use double DIP switches rather
than triple DIP switches. These DIP switches operate the same as the two bottom DIP
switches in the RS232/422/485 ports.

TX On

RX On

TX SD

RX SD

Switch 1

Switch 2

RS-422 Mode

TX On

RX On

TX SD

RX SD

4-wire RS-485 Mode

TX On

RX On

TX SD

RX SD

2-wire RS-485 Mode

Figure 6. RS-422/485 only DIP Switch Settings

«
...
12
13
14
15
16
...
»

Содержание 3PCIU2


























































Отзывы:

Нет отзывов

Похожие инструкции для 3PCIU2

Бренд: West Mountain Radio Страницы: 30

Бренд: FastVDO Страницы: 16

Бренд: StarTech.com Страницы: 2

9800PRO - 128MB Dell - Radeon AGP 8x Vga DVI Tv-out DDR X2603

Бренд: ATI Technologies Страницы: 64

Бренд: Gigabyte Страницы: 36

Бренд: Magtek Страницы: 42

Бренд: Gigabyte Страницы: 34

Бренд: Linksys Страницы: 2

Бренд: ICP DAS USA Страницы: 8

Бренд: a-TroniX Страницы: 7

Бренд: Fujitsu Страницы: 38

Бренд: Fujitsu Страницы: 66

Бренд: Fujitsu Страницы: 115

Бренд: Rosewill Страницы: 7

Бренд: Rosewill Страницы: 5

Бренд: Rosewill Страницы: 22

Бренд: NESS ID TECK Страницы: 8

Бренд: SeaLevel Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды