B&B Electronics RS-232 Digital I/O Module 232SDD16 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 27

B&B Electronics RS-232 Digital I/O Module 232SDD16 Скачать руководство пользователя страница 22

232SDD16-1005 Manual

Appendix C

C-5

B&B Electronics -- PO Box 1040 -- Ottawa, IL 61350

PH (815) 433-5100 -- FAX (815) 433-5104

DBM16 Interfacing

This section will show some general examples of how to

interface the DBM16 I/O lines to external devices. Caution must be
taken not to exceed the DBM16 specifications, failure to do so could
result in damage to the DBM16 and will void the warranty.

Before connecting the DBM16 to the SDD16 module and

connecting any external device to the DBM16 determine which I/O
lines on the SDD16 module are inputs and which are outputs. Once
the inputs and outputs are known, set the jumpers on the DBM16
accordingly. Refer to Figure C.2.

Figure C.2 - DBM16 Outline Drawing

Inputs

Digital inputs are used to sense "HIGH" and "LOW" states based

on voltage levels.  This is accomplished via switch closures, contact
closures or a solid state digital signals.  Each DBM16 input is pulled
up through a resistor and will be read as a logic "1" (HIGH) by the
SDD16 module.  When an input on the DBM16 is grounded (below
+1.5Vdc), a logic "0" (LOW) will be read by the SDD16 module.
Figures C.3 - C.6 show examples of some typical input interfaces.

C-6 Appendix

C

232SDD16-1005

Manual

B&B Electronics -- PO Box 1040 -- Ottawa, IL 61350

PH (815) 433-5100 -- FAX (815) 433-5104

Figure C.3 - Switch Input

Figure C.4 - Solid State Input

Figure C.5 - Isolated Mechanical Input

«
...
20
21
22
23
24
...
»

Содержание RS-232 Digital I/O Module 232SDD16




























Отзывы:

Нет отзывов