B&B Electronics MAP450D-004 MAP450D Скачать руководство пользователя страница 9

Страница: 9 / 20

2.1. RS-232 (Interactive & Block modes)

Interactive and Block modes support the 3-wire RS-232 configuration with TXD,

RXD and signal common. The cable requires an overall shield to protect against

electrical noise. Xon and Xoff can be used for communication handshaking.

3-Wire RS-232

Host Controller

MAP450D Terminal Block

TXD

Pin 9

RXD

Pin 10

TXD

Signal Ground

Pin 8

Return

2.2. RS-422/485 (Interactive & Block modes)

Interactive and Block modes support the 3-wire and 5-wire RS-422/485

configurations. The 3-wire configuration has both transmit and receive on the same

pair of wires plus a signal common. The 5-wire configuration has differential signal

pairs for transmit and receive plus a signal common. In both configurations the

signal pairs must be twisted and surrounded by an overall shield.

NOTE:

When using 3-wire RS-422/485, Jumper JP4 must be in position “B”.

Refer to section 2.4 for instructions.

3-Wire RS-422/485

Host Controller

MAP450D Terminal Block

TXD+ & RXD+

Pins 4 & 6

RXD+ & TXD+

TXD- & RXD-

Pins 5 & 7

RXD- & TXD-

Signal Ground

Pin 8

Return

5-Wire RS-422/485

Host Controller

MAP450D Terminal Block

TXD+

Pin 4

RXD+

TXD-

Pin 5

RXD-

RXD+

Pin 6

TXD+

RXD-

Pin 7

TXD-

Signal Ground

Pin 8

Return

INSTALLATION MANUAL

1010-0046A, REV 00

Содержание MAP450D-004 MAP450D





















Результаты поиска

Содержание MAP450D-004 MAP450D

Отзывы:

Похожие инструкции для MAP450D-004 MAP450D

Бренды по названию

Популярные бренды

B&B Electronics MAP450D-004 MAP450D, Руководство по установке

Результаты поиска

Содержание MAP450D-004 MAP450D

Отзывы:

Похожие инструкции для MAP450D-004 MAP450D

Бренды по названию

Популярные бренды