background image

 

O

PERATING 

I

NSTRUCTIONS

T

URBIDITY 

L

IMIT

-V

ALUE 

E

VALUATION 

U

NIT 

TURBISWITCH

 

GS4

WITH 

M

EASURING 

S

ENSOR OR 

I

MMERSION 

P

ROBE

 

BAMO IER GmbH 

 Pirnaer Str. 24

 D-68309 Mannheim, Germany

 

Phone: +49 (0)621 84224-0 

 Fax: +49 (0)621 84224-90, e-mail: [email protected]   

   Internet: www.bamo.de 

SU3547f.doc

   12/18 

1

 

 

Evaluation Unit 

Measuring Sensor (for installation in piping) 

Immersion Probe 

TURBISWITCH GS4  

TURBISWITCH GA1 

TURBISWITCH GA5 

TURBISWITCH GA11 

TURBISWITCH CP2 

 

Safety Precautions: 

 

  Installation, initial start-up and maintenance may only be performed by trained personnel! 

  The device may only be connected to power which complies with the specifications included in the technical data and on the 

serial plate! 

  The device must be disconnected from all sources of power during installation and maintenance work! 

  The device may only be operated under the conditions specified in the operating instructions! 

 

Functions Description: 

 

TURBISWITCH GS4

 evaluation unit with required measuring sensor for installation in piping, 

TURBISWITCH GA1, GA5, GA11

 

or 

TURBISWITCH CP2

 immersion probe

 

Turbidity measurement is based on the absorption process, i.e. it reacts to reduced light due to suspended sediment in the 
liquid. Measurement is insensitive to extraneous light thanks to the use of pulsed infrared light. Measuring sensitivity depends 
on the length of the measuring section. The shorter the measuring section, the more turbid the liquid can be. 
Pulsed infrared light is transmitted from the emitter through the liquid to the receiver. If the selected turbidity value is exceeded 
or fallen short of, the output relay in the switching amplifier reacts. 

 

 

Digital communication between the devices 

 

Turbidity dynamics for the overall sensing range: >100dB 

 

Measuring sensor for installation in piping: max. roughly 10,000 FAU (depending on diameter) 

 

Immersion probe for open containers or troughs: max. roughly 30,000 FAU 

 

3 adjustable measured value ranges (low / medium / high) 

 

1 floating changeover contact

 (both contacts are open when supply power is switched off)

 

 

1 floating alarm output contact 

 Adjustable 

delay 

time 

 Adjustable 

hysteresis 

 

Attention! Operation of the previous version of the turbidity emitter and receiver (TT-GS and TR-GS), as well as the CP1 
immersion probe, is only possible with the TRUBOMAT GS3 turbidity limit monitor. 

 

Technical Data: 

 

Supply power:  

 

 

100 - 255V AC / 50 - 60Hz (TURBISWITCH GS4 G) 

(see type plate)  

 

 

10 - 3V DC and 12 - 24V AC (TURBISWITCH GS4 D) 

 

Power consumption:   

 

1 - 5W 

 

Ambient temperature:

 

  -10…+45°C 

 

Output relay switching capacity: 

250V AC, 3A / 30V DC, 1A 

 

Caution: Contacts are not protected against overload – use external 
protective device! 

 

Housing:      

22.5x100x122mm, IP40, for top-hat rail: 35x7.5mm (DIN EN 50 022) 

 

Terminals: 

 

 

 

Screw terminal for wire cross-sections of up to 1.5mm² 

 

Max. cable length:

 

  100m 

 

Threshold value adjustment:

   

3 x 0  - 100% range, low (5% steps), medium (2% steps),

 

high (1% steps) 

Содержание TURBISWITCH GS4








Отзывы: