28
29
cordless
cordless
Operation
Preparation
• Carefully remove the hand blender and all accessories from the packaging.
• Remove all packaging components and keep the complete packaging.
• Clean the hand blender and its accessories before they come into contact with
food. See “Cleaning and care” (page 28).
Setting up the hand blender and electrical preparation
•
Plug the charger cable into the base of the charger, then in-
sert the cable into the slot provided and pull the cable out-
wards.
Attention: only cable duct 2 may be used!
•
Place the charger (fig. 2) on a flat, non-slip surface in the im-
mediate vicinity of a mains outlet.
• Insert the plug into the mains socket.
• Place the hand blender in the charger until the battery is fully charged. Upon deliv-
ery, the battery is only partially charged.
LED display (charging and working)
LED display: blender is in the charger
1–4 LEDs flashing ascending
=
battery in charging mode
4
LEDs lit briefly when placed
=
battery charged and ready for use
on charger
LED display: switching on the blender
(blender is not in the charger)
While the large
multifunction button
is pressed (1-2 seconds),
a blue light appears as confirmation for the switch-on mode. At
the same time, the 4 LEDs indicate the battery charge level.
After releasing the large multifunction button, the LEDs of the
charge level indicators go out and only the large multifunction
button lights up. As long as the multifunction button is lit, work
can be done. If the button is unlit, see further down in this chap-
ter, “LED display without light”.
When the multifunction button is pressed, the current charge status lights up for 1
second.
2
1
1
1
2
1
2
A
B
4 x
1
1
2
1
2
4 LEDs lit = full battery charge for approx. 20 minutes
3 LEDs lit = ¾ battery charge for ≥ 15 minutes operating time
2 LEDs lit = ½ battery charge for ≥ 7 minutes operating time
1 LEDs lit = ¼ battery charge for ≤ 7 minutes operating time
Recommendation: charge the battery
LED display: blender in operation
The large multifunction button lights up permanently in blue. Note: The blender will
switch itself off after 60 seconds if not used. See “LED display without LED light”.
LED display: without LED light
The LED display of the hand blender has a switch-off function (sleep function) that
activates after 60 seconds of non-use and puts the hand blender into sleep mode.
By pressing the large ON button once, the appliance is reawakened and is ready to
work. This sleep function has been built in to allow longer operation time and also to
prolong the battery life.
Operation of the bamix
®
cordless hand blender
Before you can work with the appliance, you need to affix an
attachment.
CAUTION! Risk of injury when affixing and replacing attachments.
For a detailed description, see “Affixing and replacing attachments”
(page 33).
The blades of the attachments are very sharp! CAUTION, risk of injury! Do not
use your hand to remove pieces that block the blade! Use a blunt object (e.g. a
wooden or plastic handle) for this purpose.
•
Fill a flat-bottomed receptacle or a bamix
®
blender jug (see www.bamix.com). Do
not switch on the hand blender until it is in the receptacle.
•
With coated receptacles, take care not to damage the coating. For further instruc-
tions on applications of attachments such as mixing, puréeing, whisking, etc.,
please see www.bamix.com.
Note: To protect the hand blender from being overloaded, it will switch off
automatically in the event of overheating or blade blockage. The hand blender
can then be switched on again and used.
Содержание cordless
Страница 21: ...cordless Notes...
