background image

Digital Duo Charge

Installation/Operation

R

R

Introduction

The Digital Duo Charge provides a safe, intelligent alternative for the care of your vessel’s engine starting battery. Unlike 
switches, isolators and other charge splitting devices, the Duo Charge is mounted between the vessel’s house and starting 
batteries rather than between the alternator and batteries. This allows the alternator and regulator to concentrate output 
based on the house battery’s needs. When the Duo Charge senses charging voltage at the house battery, it works like a DC-
to-DC battery charger, providing up to 30 amps of regulated charging current to support the starting battery.
In most installations, the Duo Charge requires just four wires for operation; a fused input wire, a fused output wire, a ground 
wire and an ON/OFF wire. In applications where the Duo Charge is used to supply a battery bank that may require more 
than 30 amps of regulated charging current, the Duo Charge may be used to 

manually 

control an external solenoid. Please 

note the section in the manual relating to solenoid control.
The  Duo  Charge  is  designed  specifically  to  enable  its  user  to  control  charging  voltage  output  --  making  it  possible  to 
safely mix house and starting battery technologies. The Duo Charge features four different programs based on four bat-
tery technologies: Standard Flooded, Deep Cycle Flooded, Gel and AGM battery types. In addition, the Duo Charge can be 
programmed for 12-volt or 24-volt operation. When used with an optional Battery Temperature Sensor cable (MC-TS-B), the 
Duo Charge has the ability to respond to a battery over-temperature condition by automatically discontinuing charging 
output.

Safety Considerations

Before installing your Duo Charge, please take a moment to consider these guidelines for safe regulator installation. Failure 
to work safely could result in injury or damage to your electrical system.

1.  Always disconnect your battery banks and ensure that switches are “OFF” prior to installing your regulator.
2.  Remove loose-fitting clothing or jewelry, which could become entangled in your motor or other machinery.
3.  Wear ANSI-approved safety glasses.
4.  DO NOT attempt to modify the Duo Charge. Alterations could result in damage to your charging system, and will void 

your warranty.

5.  Do not attempt installation if tired or fatigued.
6.  Ensure the engine has cooled before initiating installation.
7.  Do not attempt installation while using alcohol or medication that could impair your judgment or reaction time.
8.  Always use the right tool for the job. Improper tool use may damage regulator or your boat, and could result in per-

sonal injury.

9.  Take time to read the manual. Equipment damage and possible injuries may result from an incomplete understand-

ing of the installation and operation of the Duo Charge. If you are unfamiliar with DC electrical systems, consult with a 
licensed marine electrician. 

© Revised June, 2008

Contents

Introduction ............................................................................ 1
Safety Considerations ............................................................ 1
Unpacking The Box ................................................................ 2
Installation Basics ................................................................... 2
Wiring Basics/Ground Wire/Output Wire ........................... 2
Input Wire/ON-OFF Wire/Optional Connections .............. 3
Battery Temperature Sensor/Solenoid Drive .................... 4

Duo Charge Operation .........................................................5
Programming Duo Charge/System Voltage .....................6
Programming For Battery Type ...........................................6
Troubleshooting ....................................................................7
Duo Charge Wiring Diagram ...............................................7
Duo Charge Terminal Location Legend .............................8
Balmar Contact Information ................................................8

1

Содержание Digital Duo Charge









Отзывы: