manualshive.com logo in svg

Baldor STANDBY PERMANENT MOUNT SERIES, Руководство оператора

Поделиться
Скачать
Baldor STANDBY PERMANENT MOUNT SERIES Скачать руководство пользователя страница 39

OVERHEATING (continued) 

 

CAUSE     CHECK 

AND 

REMEDY 

 

High room temperature. 

 

 

Improve ventilation. 

 

Insufficient 

circulation.   Provide 

cross-ventilation. 

 

Low power factory. 

Reduce inductive loads or install power factor 
improvement capacitors. 

 

Unbalanced load 

The load on each leg should be as evenly balanced as 
possible and should not exceed the rated current on 
any leg. 

 

Dry 

bearing. 

    Replace 

bearing. 

 
 
 

MECHANICAL NOISE 

 

CAUSE     CHECK 

AND 

REMEDY 

 

Defective 

bearing. 

   Replace 

bearing. 

 

Rotor scrubbing on stator. 

 

 

Bad bearing; replace. Bent shaft, return to factory. 

     Loosen 

end 

bell, 

tighten; 

loose 

drive 

discs, 

tighten. 

 

Loose 

laminations. 

   Return 

to 

factory. 

 

Loose or misaligned coupling. 

 

Tighten or align. 

 
 

GENERATOR FRAME PRODUCES SHOCK WHEN TOUCHED 

 

CAUSE     CHECK 

AND 

REMEDY 

 

Static 

charge. 

    Ground 

generator 

frame. 

 

Grounded armature or field coil. 

 

Return to factory for repair. 

 
 
 
 
 
 
 
 
 
 

 
 
 
 
 

 

Содержание STANDBY PERMANENT MOUNT SERIES

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды