background image

(A42086) – Rev. B – 7/2000

V.  LIMITED WARRANTY

For a period of 2 years from date of original purchase, BALDOR will repair or replace without charge
controls which our examination proves to be defective in material or workmanship.  This warranty is
valid if the unit has not been tampered with by unauthorized persons, misused, abused, or improperly
installed and has been used in accordance with the instructions and/or ratings supplied.  This warran-
ty  is  in  lieu  of  any  other  warranty  or  guarantee  expressed  or  implied.    BALDOR  shall  not  be  held
responsible  for  any  expense  (including  installation  and  removal),  inconvenience,  or  consequential
damage, including injury to any person, caused by items of our manufacture or sale.  (Some states do
not allow the exclusion or limitation of incidental or consequential damages, so the above exclusion
may not apply.)  In any event, BALDOR’s total liability, under all circumstances, shall not exceed the
full purchase price of the control.  Claims for purchase price refunds, repairs, or replacements must be
referred to BALDOR with all pertinent data as to the defect, the date purchased, the task performed by
the control, and the problem encountered.  No liability is assumed for expendable items such as fuses.

Goods  may  be  returned  only  with  written  notification  including  a  BALDOR  Return  Authorization
Number and any return shipments must be prepaid.

Baldor Electric Company

5711 R. S. Boreham, Jr. Street

Fort Smith, AR  72902-2400  U.S.A

(501) 646-4711  Fax (501) 648-5792

International Fax (501) 648-5895

Содержание BC145















Отзывы: