background image

frame until the be drill bit hits the inside face of the mounting 
bracket on the outside face.

19. Repeat the process on the other receiver.

20. Insert the metal risers into the receivers and secure them at 

the desired height with the riser pin.

INSTALL CORNER BRACKETS

Locate the four L-shaped brackets that go on the top and bottom 
of each inner corner at the head-end of the Reformer frame. 
These corner brackets provide additional support for the Tower 
bracket.

21. Use the provided 21/64” drill bit (larger drill bit). Slowly drill (4)

four holes through the frame from the outside using the 
bracket to guide the holes (See Figure K).

22. From the outside of the head- 

end of the frame, insert a 
2-1/4” button head screw and 
a 1/4” washer into the holes 
drilled (See Figure K).

23. Place corner brackets with 

the short flange on the inside 
head-end of the frame and 
the longer flange flush on 
the inner, long side of the 
Reformer (See Figure L).

24. Secure the corner bracket with 1/4” washer and a small nylock 

nut. Make sure bracket fits tightly against the side rail and is 
level.

25. Using the 21/64” drill bit, from the inside of the frame drill 

through the hole in the long side of the corner bracket and 
drill into the frame. Drill slowly with light pressure.  

Note

: Be particularly careful drilling-- it is easy to splinter the 

outside of the frame. Hold the drill steady and level - it is a 
good idea to use two hands during this step.

26. From the outer side of frame, 

insert carriage bolt into drilled 
hole (See Figure M).

27. Secure on inner side with 

5/16” large nylock nut.

28. Repeat steps 26-28 on the other corner brackets.

INSERT VERTICAL TOWER TUBES

29. Loosen setscrews on circular tube receivers on the Tower 

bracket using the 3/16” Allen wrench (See Figure N). 

30. Remove the vertical tower 

system and place them into 
the receiver bracket on the 
end of the Reformer. The 
knobs of the sliders will be 
facing outwards as shown in 
Figure O. Make sure when you place the tubes into the 
receiver that the loop is facing forward, towards the carriage, 
see Figure P.

HOW TO ADJUST YOUR SLIDING PUSH THROUGH BAR

Position your hands on the outside of each slider.  Place your 
middle and/or ring fingers under the silver base of the knob; right 
where the black body of the knob threads into.  Place your index 
finger and thumb around the knob itself.  Pull each of the knobs 
outwards, away from the vertical tubes, until they stop.  Using the 
same force on each arm, move the slider upwards or downwards 
to each new location.  Once you near a new location slightly 
release the outward pull of the knobs. The pins will automatically 
fall into the next position when aligned.  

WEEKLY MAINTENANCE

Inspect springs for separations, and replace if needed. Inspect 
snaps on springs and make sure the retractors operate smoothly. 
Replace them if worn or do not operate freely. Make sure that 
there are no indentations on the inside of the hooks.

Inspect all nuts, eyebolts and setscrews for tightness. Tighten or 
replace if necessary.

It is recommended to check to ensure the pins in the plunger 
knobs protrude and lock into the vertical tubes. First pull both 
knobs out and start moving the sliders to a different position.  
Release the knobs before the next hole and continue to slide the 
system. Once over a hole the pin of the knob will drop into the 
opening. Once each slider is in a new position apply a down force 
on the PTB directly downwards. The pins of the sliders should 

 Figure K: Drill holes through areas 
indicated.

Figure L: Corner bracket mounting 
location.

Long Side

Short Side

Figure M: Carriage bolt locations.

Figure N: Insert Tower tubes into tube 
receivers.

Figure O

Knobs 
outward

Figure P

Loop should face 
the reformer.

3

Отзывы: