Baker Hughes Panametrics dew.IQ Скачать руководство пользователя страница 84

Страница: 84 / 130

5.6 Reading and setting the calibration references

Note:

This section applies only to an M Series probe. The Cal Reference menu is not available for an

IQ.probe

Note:

Access to this menu requires a passcode (see “Entering Your Passcode” on page 67 ).

IMPORTANT:

The

dew.IQ

is factory programmed with high and low reference MH values. These values are generated from a factory lab

calibration and should not be changed without first consulting Panametrics technical support. Changes to these values will

alter the accuracy of your measurements.

To update the calibration references, from the Settings Menu select Cal Data and press

Enter

. Then, enter your passcode and press

Enter

. The following screen appears:

To view or edit the calibration reference settings, select Cal Reference and press

Enter

Proceed to the next section.

Содержание Panametrics dew.IQ



































































































































Результаты поиска

Содержание Panametrics dew.IQ

Отзывы:

Похожие инструкции для Panametrics dew.IQ

Бренды по названию

Популярные бренды

Baker Hughes Panametrics dew.IQ, Руководство пользователя

Результаты поиска

Содержание Panametrics dew.IQ

Отзывы:

Похожие инструкции для Panametrics dew.IQ

Бренды по названию

Популярные бренды