Baker Hughes Druck DPI 610 IS Скачать руководство пользователя страница 11

Страница: 11 / 76

English–DPI 610/615 IS Instruction Manual | 1

General

1. Introduction

1.1 General

The DPI

610

IS and DPI

615

IS intrinsically safe instruments measure and display pneumatic and

hydraulic pressure applied to the test port.Pressure measurement can be absolute, gauge and

sealed gauge and in ranges from 2.5 mbar to 700 bar (1.0 inH

O to 10000 psi).

Calibrator versions of this instrument contain pneumatic or hydraulic pressure generation

components to produce pneumatic pressure ranges between -1 to 20 bar (-14.5 psi to 300 psi)

and hydraulic pressure ranges up to 400 bar (6000 psi).
Using external electrical connections, the DPI

610

IS and DPI

615

IS intrinsically safe

instruments measure ±30 V dc and ±55 mA. An integral sensor provides measurement of ambient

temperature. Additional sensors (option B1) connect to an external connector and extend the

pressure measurement range and include differential pressure measurement. The DPI

615

instrument has an RS232 connector to enable downloading of test data to a compatible

documenting system. Six alkaline C size batteries, IEC Type LR14, power the instrument.

1.2 Description of Procedures

The procedures apply to both the DPI 610 IS and the DPI 615 IS instruments unless otherwise

stated. In the procedures in this manual, hard (fixed function) and soft (variable function) key

operations are shown in bold type:

TASK

and

. These statements mean press the

TASK

key

and press the

key. Soft key operations can be assigned to both the

and

keys. Where a

specific soft function is referred to it is written in bold italics (e.g.)

PROCESS

This instrument has a number of operating modes that are described in simplified form in the

following sections. Diagrams accompanying the procedures give typical selection sequences and

shaded controls indicate that this control key should be pressed in the appropriate sequence.

Diagrams should be read from left to right, top to bottom where appropriate. A shaded display soft

box indicates that the function key immediately below that soft box should be pressed (either

for the left hand soft box or

for the right).

In the above diagram the following key sequence is indicated.
a. Press the F2 key (the key immediately below the

UNITS

soft box).

b. Use the

and

Down

cursor keys (only) to select the required option. (If all keys shaded,

use all these keys to select or enter data).

c. Press the

ENTER

key.

INFORMATION

Zinc-carbon and zinc-chloride cells must not be used in this

instrument. Use only the battery types as shown in “Batteries” on page

ii.

SELECT UNITS

TASK : BASIC

VOLTAGE

PRESSURE INT

CURRENT

PRESSURE

UNITS

SELECT UNITS
OF PRESSURE

Содержание Druck DPI 610 IS







































































Результаты поиска

Содержание Druck DPI 610 IS

Отзывы:

Похожие инструкции для Druck DPI 610 IS

Бренды по названию

Популярные бренды

Baker Hughes Druck DPI 610 IS, Инструкция по эксплуатации

Результаты поиска

Содержание Druck DPI 610 IS

Отзывы:

Похожие инструкции для Druck DPI 610 IS

Бренды по названию

Популярные бренды