Baker Hughes DigitalFlow XGF868i Скачать руководство пользователя страница 23

Страница: 23 / 100

1.9.1c Selecting mass flow units

1. Scroll to the desired

mass flow

units for the flow rate

display and press [enter]. The available units for this

prompt are determined by the selection made at

system units (see

Table 6

below).

Table 6: Available mass flow units

English

Metric

LB = pounds

KG = kilograms

KLB = thousands of LB

Tonne = metric tons (1,000 KG)

MMLB = millions of LB

Tons (2,000 LB)

2. Scroll to the desired

mass flow time

units for the mass

flow rate display and press [enter].

3. Scroll to the desired number of

Mdot decimal digits

(digits to the right of the decimal point in the mass flow

rate display) and press [enter].

4. Scroll to the desired

mass (totalizer)

units for the totalized

mass flow rate display and press [enter]. The available

units for this prompt are determined by the selection

made at the system units prompt.

5. Scroll to the desired number of

mass decimal digits

(digits to the right of the decimal point in the totalized

mass flow rate display) and press [enter].

Procedure options

After completing the previous steps, the XGF868i returns to

the global

program

window. Do one of the following:

• To continue programming, refer to

Appendix A. Menu

Maps on page 39

, to navigate to the desired menu.

• To leave the

keypad program

, press [escape] twice.

1.9.2 Setting up inputs and outputs

Set up the XGF868i inputs and outputs via the I/O submenu.

While following the programming instructions, refer to

Figure

30 on page 42

and

Figure 31 on page 43

The following

three submenus are included in this section:
•

Error

- program the meter’s response during an error

condition (see below)

•

Optn

- set up any option cards and the slot 0 analog

outputs (see

Setting up slot 0 and slot 1 inputs/outputs on

page 14

)

•

LCD

- set up the LCD display. Refer to

Chapter 2.

Displaying data on page 23.

NOTE:

In this section, slot 1 appears as an option only if a

suitable option card is installed in slot 1.

Proceed to the appropriate section to program the

option selection made at the above prompt. Remember

to record all programmed data in

Appendix B. Data records

on page 45

1.9.2a Selecting error handling

This menu option permits programming of the manner

in which the XGF868i outputs respond during an error

condition. See

Chapter 2, error codes

, in the

Service

manual

for a discussion of the built-in error codes. To

access this submenu:

NOTE:

The 2-channel meters have an additional option

for error handling.

1. In the

keypad program

, scroll to

prog

and press [enter].

2. In the

prog

menu, scroll to

globl

and press [enter].

3. In the global

program

menu, scroll to I/O and

press [enter].

4. Scroll to

error

and press [enter].

5. Scroll to the desired option for error handling and press

[enter]. If you select error level in mA, proceed to step

6 on the next page. (See

Table 7 on page 14

for a

description of error handling options available and how

the totalizers and analog outputs respond to them.)

NOTE:

The error responses listed in

Table 7 on page 14

apply only to the channelx measurement mode and to

the sum/difference measurement modes, if either or

both channels are in error. Error handling in the Average

measurement mode is set in

step 7 on page 14

Содержание DigitalFlow XGF868i





































































































Результаты поиска

Содержание DigitalFlow XGF868i

Отзывы:

Похожие инструкции для DigitalFlow XGF868i

Бренды по названию

Популярные бренды

Baker Hughes DigitalFlow XGF868i, Руководство по программированию

Результаты поиска

Содержание DigitalFlow XGF868i

Отзывы:

Похожие инструкции для DigitalFlow XGF868i

Бренды по названию

Популярные бренды