Bailey Unicorn 2, Руководство по обслуживанию

Страница: 14 / 36

14
Bulb Replacement
Unicorn Tail, Indicator, reverse, brake and fog.
1. 5HPRYH WKH o[LQJ VFUHZV ZKLOVW VXSSRUWLQJ
WKH UHDU OLJKW .HHS WKH VFUHZV VDIHO\ UHDG\
IRU UHoWWLQJ WKH OLJKW 'R QRW DWWHPSW WR XVH
any alternative screws which could damage the
rear light or caravan panel.
2. Pull the rear light towards you from the side
ZLWK WKH o[LQJ KROHV 7KLV ZLOO UHOHDVH WKH
2-hooks which locate into the caravan panel
and will allow you to see the back of the rear
light.
Remove the bulb holder with the failed bulb
from the rear light by turning the bulb holder
anti-clockwise, remove the failed bulb from the
EXOE KROGHU DQG oW WKH FRUUHFW UHSODFHPHQW
There is a diagram on the lower part of the light
ZKLFKVKRZVWKHEXOEW\SHWREHoWWHG5HSODFH
the bulb holder by inserting into the hole and
turn clockwise to lock into position. Ensure all
seals are correctly located.
4. Offer the rear light back into the caravan panel,
ensure the 2-location hooks are engaged and
WKHQUHSODFHWKHUHDUOLJKWo[LQJVFUHZV
Do not over tighten! Maximum torque is 80
Ncm
Check for correct operation of all light functions.
Pegasus GT65 Tail, Indicator, reverse, Brake and
Fog.
1. Using a Pozi-Drive screwdriver remove carefully
the screws visible on the failed lamps lens,
support the lens so it cannot fall.
Function dependant
2. For the Indicator bulb remove the bulb by
turning anticlockwise with slight pressure on
the bulb.
Replace Bulb with a new 12V 21W Clear Bulb
aligning the pins correctly prior to installation.
Install new bulb with slight pressure and turn
clockwise.
4. For the Stop Tail bulb remove the bulb by turning
anticlockwise with slight pressure on the bulb.
5HSODFH%XOEZLWKDQHZ9:&OHDU%XOE
aligning the pins correctly prior to installation.
Install new bulb with slight pressure and turn
clockwise.
6. For the Fog bulb remove the bulb by turning
anticlockwise with slight pressure on the bulb.
7. Replace Bulb with a new 12V 21W Clear Bulb
aligning the pins correctly prior to installation.
Install new bulb with slight pressure and turn
clockwise.
8. For the Reverse bulb remove the bulb by turning
anticlockwise with slight pressure on the bulb.
9 Replace Bulb with a new 12V 21W Clear
Bulb aligning the pins correctly prior to installation.
Install new bulb with slight pressure and turn
clockwise.
Upper Side position lamps
1. Remove lens from base to access bulb.
2.
&DUHIXOO\ LQVHUW D VPDOO pDW KHDG VFUHZGULYHU
into the recess in the lower edge of the lamp
base. Apply pressure to the locking base.
Lift lens upwards and away from the lamp base,
!
Road Lights Bulb Type Bulb Rating
Front Marker Lights LED 12v/ <1 watt
Side Marker Lights (Low Level) LED 12v/ <1 watt
Side Marker Lights (High Level) R5W 12v/ 5 watt
Brake Light (High Level) LED 12v/ <1 watt
Number Plate Light Festoon 12v/ 10 watt
Tail Light R10 12v/ 10 watt
Direction Indicator Light PY21 12v/ 21 watt
Reversing Light P21 12v/ 21 watt
Brake Light (Low Level) P21 12v/ 21 watt
Fog Light P21 12v/ 21 watt
Fuse MCB Specifications Chart
Fuses
Alarm 5 amp (yellow) Pump
Fridge Ignition 5 amp (yellow) Aux Socket
Caravan Battery 15 amp (blue) Radio/Aerial
Fridge Ignition 15 amp (blue) Alde Water heater
Caravan Battery 15 amp (blue) Alde central Heating
Lights 1 15 amp (blue) Refrigerator
Lights 2 15 amp (blue) Smoke Alarm Battery
Ignitions 5 amp (yellow) CO alarm Battery
PIR alarm Battery