manualshive.com logo in svg

Bailey Infi 90 INNIS01, Инструкция, Страница: 40 / 61

Поделиться
Скачать
Bailey Infi 90 INNIS01 Скачать руководство пользователя страница 40

TROUBLESHOOTING

INNPM11 MODULE ERROR CODES

5 - 2

  

WBPEEUI250016A1

®

 

INNPM11 MODULE ERROR CODES

If errors occur while the NPM module is operating, the status
LED turns red and the CPU LEDs on the NPM module faceplate
display error codes. Table 

5-2

 lists the NPM module error codes

and associated corrective action. The NPM module displays
error codes only when it is halted.

Table 5-2.  INNPM11 Module Error Codes

Code

LEDs

8 7 6 5 4 3 2 1

Condition

Corrective Action

0D

0 0 0 0 1 1 0 1

Intermodule link errors

Check I/O expander bus connection 
between primary and secondary NPM 
modules.

0E

0 0 0 0 1 1 1 0

Dipswitch SW3 position 8 is set 
the same on redundant NPM 
modules

Change position 8 on one of the NPM 
modules. Check for another module at NPM 
Controlway address.

12

0 0 0 1 0 0 1 0

NIS handshake failure

Replace NIS or NPM.

13

0 0 0 1 0 0 1 1

ROM checksum error

Reset NPM, replace NPM if error continues.

14

0 0 0 1 0 1 0 0

I/O expander bus message failure

15

0 0 0 1 0 1 0 1

Loopback test failure

Check cabling and termination device. 
Replace NIS.

31

0 0 1 1 0 0 0 1

Memory or CPU fault

Replace NPM.

32

0 0 1 1 0 0 1 0

Address or bus error

Reset NPM. replace NPM if error continues.

33

0 0 1 1 0 0 1 1

Illegal instruction

34

0 0 1 1 0 1 0 0

Trace/privilege violation

35

0 0 1 1 0 1 0 1

Spurious/unassigned exception

36

0 0 1 1 0 1 1 0

Divide by 0/checksum/format error

38

0 0 1 1 1 0 0 0

Option dipswitch settings do not 
match between primary and 
backup NIS or NPM modules.

Check option dipswitches settings.

39

0 0 1 1 1 0 0 1

Duplicate node number on loop

Change node number. Check primary and 
backup NPM configuration (NKMP01/11 
cable not installed).

3C

0 0 1 1 1 1 0 0

Relay or fuse failure on 
termination device or power supply 
failure

Check relay or fuse. Check power supply. 
Replace termination device if error 
continues.

3D

0 0 1 1 1 1 0 1

Incompatible NIS module firmware NPM firmware revision C.1 or later requires 

NIS firmware revision E.1 or later.

3F

0 0 1 1 1 1 1 1

NPM has stopped because the 
user pressed the stop button

Reset NPM.

NOTE: Codes are displayed only when the NPM is halted and the status LED is red. 0 = LED OFF, 1 = LED ON.

Содержание Infi 90 INNIS01






























































Отзывы:

Нет отзывов