manualshive.com logo in svg

Bailey INFI 90 IMASO01, Инструкция

Поделиться
Скачать
Bailey INFI 90 IMASO01 Скачать руководство пользователя страница 30

INTRODUCTION

I-E96-303A   

5 - 1

SECTION 5 - TROUBLESHOOTING

INTRODUCTION

This section explains the error indications and corrective
actions for the Analog Slave Output (ASO) module.

ERROR INDICATIONS AND CORRECTIVE ACTION

You can obtain the status of the ASO through an INFI 90 oper-
ator interface (e.g., Operator Interface Station, Engineering
Work Station, Configuration and Tuning Terminal) or the front
panel module status LED indicator.

Status LED

The front panel status LED has three states to indicate normal
operation and error conditions. Table 

5-1

 lists ASO status LED

states, error indications, probable causes and corrective
actions.

NOTE: 

If the corrective actions in Table 

5-1

 do not correct a problem

with the ASO module, replace it.

Master Module Errors

The Multi-Function Processor (MFP) performs status checks on
the ASO. An error will appear in the report function of an oper-
ator interface. Refer to the Product Instruction for the operator
interface you are using for an explanation of these reports.

Function Code (FC) 149 output block N+7 in the MFP configu-
ration is the ASO status flag (logic 0=good; logic 1=bad). You
can use an operator interface to monitor this block. If the sta-
tus flag is a logic 1, check the front panel module status LED
and the operator interface report function to determine correc-
tive actions.

NOTE: If FC 149 specification 3 is set to 0, the MFP will trip when
the ASO module fails. Changing specification 3 to a 1 allows the
MFP to continue to operate if any ASO error condition exists.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание INFI 90 IMASO01












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды