background image

 

 

Force Majuere.

 Seller shall not be responsible for any delay in the delivery of, or failure to deliver, Goods due to 

ca

uses beyond Seller’s reasonable control including, without limitation, acts of God, acts of war or terrorism, enemy 

actions,  hostilities,  strikes,  labor  difficulties,  embargoes,  non-delivery  or  late  delivery  of  materials,  parts  and 
equipment  or  transportation  delays  not  caused  by  the  fault  of  Seller,  delays  caused  by  civil  authorities, 
governmental regulations or orders, fire, lightening, natural disasters or any other cause beyond Seller's reasonable 
control. In the event of any such delay, performance will be postponed by such length of time as may be reasonably 
necessary to compensate for the delay. 
 

Installation.

  If  Buyer  purchases  any  Goods  that  require  installation,  Buyer  shall,  at  its  expense,  make  all 

arrangements  and  connections  necessary  to  install  and  operate  the  Goods.  Buyer  shall  install  the  Goods  in 
accordance  with  any  Seller  instructions  and  shall  indemnify  Seller  against  any  and  all  damages,  demands,  suits, 

causes of action, claims and expenses (including actual attorneys’ fees and costs) arising directly or indirectly out 

of Buyer’s failure to properly install the Goods. 
 

Work  By  Others;  Safety  Devices.

  Unless  agreed  to  in  writing  by  Seller,  Seller  has  no  responsibility  for  labor  or 

work performed by  Buyer or others, of any nature, relating to  design, manufacture, fabrication, use, installation or 
provision of Goods. Buyer is solely responsible for furnishing, and requiring its employees and customers to use all 
safety devices, guards and safe operating procedures required by law and/or as set forth in manuals and instruction 

sheets furnished by Seller. Buyer is responsible for consulting all operator’s manuals, ANSI or comparable safety 
standards,  OSHA  regulations  and  other  sources  of  safety  standards  and  regulations  applicable  to  the  use  and 
operation of the Goods. 
 

Remedies.

  Each  of  the  rights  and  remedies  of  Seller  under  this  Agreement  is  cumulative  and  in  addition  to  any 

other or further remedies provided under this Agreement or at law or equity. 
 

Attorney’s  Fees.

  In  the  event  legal  action  is  necessary  to  recover  monies  due  from  Buyer  or  to  enforce  any 

provision  of  this  Agreement,  Buyer  shall  be  liable  to  Seller  for  all  costs  and  expenses  associated  therewith, 

including Seller’s actual attorneys' fees and costs. 
 

Governing  Law/Venue.

  This  Agreement  shall  be  construed  and  governed  under  the  laws  of  the  State  of 

Wisconsin, without application of conflict of law principles. Each party agrees that all actions or proceedings arising 
out of or in connection with this Agreement shall be commenced, tried, and litigated only in the state courts sitting in 
Manitowoc  County, Wisconsin  or  the  U.S.  Federal  Court  for  the  Eastern  District  of Wisconsin. Each  party  waives 

any right it may have to assert the doctrine of “forum non conveniens” or to object to venue to the extent that any 
proceeding  is  brought  in  accordance  with  this  section.  Each  party  consents  to  and  waives  any  objection  to  the 
exercise of personal jurisdiction  over it by courts  described in this section. Each  party  waives to the fullest  extent 
permitted by applicable law the right to a trial by jury. 
 

Summary of Return Policy. 

  10  Day  acceptance  period  from  date  of  delivery.  Damage  claims  and  order  discrepancies  will  not  be  accepted 

after this time. 

  You must obtain a Baileigh issued RGA number PRIOR to returning any materials. 

  Returned materials must be received at Baileigh in new condition and in original packaging. 

  Altered items are not eligible for return. 

  Buyer is responsible for all shipping charges. 

  A 30% re-stocking fee applies to all returns. 

 
Baileigh  Industrial  makes  every  effort  to  ensure  that  our  posted  specifications,  images,  pricing  and  product 
availability  are  as  correct  and  timely  as  possible.  We  apologize  for  any  discrepancies  that  may  occur.  Baileigh 
Industrial reserves the right to make any and all changes deemed necessary in the course of business including but 
not limited to pricing, product specifications, quantities, and product availability. 
 

For Customer Service & Technical Support: 

Please contact one of our knowledgeable Sales and Service team members at: 
(920) 684-4990 or e-mail us at [email protected] 

Содержание BB-9616M









































Отзывы: