Baicells BS6430E Скачать руководство пользователя страница 24

 

 

 

22 

 

compliance could void the user's authority to operate the equipment. 

This equipment has been tested and found to comply with the limits for a Class B digital 
device,  pursuant  to  part  15  of  the  FCC  Rules.  These  limits  are  designed  to  provide 
reasonable  protection  against  harmful  interference  in  a  residential  installation.  This 
equipment generates uses and can radiate radio frequency energy and, if not installed 
and used in accordance with the instructions, may cause harmful interference to radio 
communications.  However,  there  is  no  guarantee  that  interference  will  not  occur  in  a 
particular  installation.  If  this  equipment  does  cause  harmful  interference  to  radio  or 
television reception, which can be determined by turning the equipment off and on, the 
user  is  encouraged  to  try  to  correct  the  interference  by  one  or  more  of  the  following 
measures: 

 

Reorient or relocate the receiving antenna. 

 

Increase the separation between the equipment and receiver. 

 

Connect  the  equipment  into  an  outlet  on  a  circuit  different  from  that  to  which  the 
receiver is connected. 

 

Consult the dealer or an experienced radio/TV technician for help. 

Warning: 

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled 
environment. This equipment should be installed and operated with minimum distance 
70cm between the radiator & your body. 

 

ISEDC Compliance

 

This device complies with Innovation, Science, and Economic Development 
Canada licence-exempt RSS standard(s).  

Operation is subject to the following two conditions:  

(1) This device may not cause interference, and  

(2) This device must accept any interference, including interference that may cause u

ndesired operation of the device. 

 

Le présent appareil est conforme aux CNR d' Innovation, Science et Développement 

é

conomique Canada applicables aux appareils radio exempts de licence. 

L'exploitation est autorisée aux deux conditions suivantes:               

(1) l'appareil ne doit pas produire de brouillage, et  

(2) l'utilisateur de l'appareil doit accepter tout brouillage 

radioélectrique subi, même si le brouillage est                                          

Содержание BS6430E


























Отзывы: