Baelz Automatic 373-E07 страница 35 Скачать руководство пользователя

Страница: 35 / 36

BA_373-E07_04_DEF_MJ_1821

35 |

W. Baelz & Sohn GmbH & Co.

· Koepffstrasse 5 · 74076 Heilbronn · Germany ·

www.baelz.de Seite | Page

Motorized Linear Actuator

baelz 373-E07

Malfunction

Cause

Action required

Actuator not working

Power failure

Determine the cause and correct the

problem.

Defective fuse (in control cabinet)

Determine the cause and correct the

problem, replace the fuse.

Linear actuator incorrectly connected

Re-connect as specified on circuit

diagram (inside cover).

Short circuit caused by humidity

Determine the cause, dry the linear

actuator; if necessary, replace cover

seal and screws and/or fit protective

cover.

Short circuit caused by incorrect connection Connect correctly.

Motor winding damage caused, for example,

by high voltage or defective electronics

Determine cause, measure current

data, compare with nameplate and

specifications, dismantle linear

actuator and return for repair.

Voltage drop due to connecting cables being

too long and / or having insufficient cross-

section

Measure current data with linear

actuator, recalculate connecting

cables and replace as necessary.

Actuator running erratically,

constantly opening and

closing

Power fluctuations exceed permissible

tolerance

Improve power supply conditions.

Loose contact in supply line

Check and tighten connections

(terminal blocks).

Actuator stops intermittently

Valve jamming

Enable smooth valve movement.

Actuator does not move to

end position. Valve fails to

open / close

System pressure too high

Adjust system pressure.

Poor input signal

- interfering signals

- signal fluctuation

Check input signal at linear actuator,

correct the problem causing the

malfunction.

Linear actuator fails to move

or does not move correctly

to the position defined by

the input signal.

Circuit board defective

Replace circuit board, if necessary

dismantle actuator and return for

repair.

10.1 Checklist for operational malfunctions

Содержание 373-E07





































Результаты поиска

Содержание 373-E07

Отзывы:

Похожие инструкции для 373-E07

Бренды по названию

Популярные бренды

Baelz Automatic 373-E07, Руководство по эксплуатации

Результаты поиска

Содержание 373-E07

Отзывы:

Похожие инструкции для 373-E07

Бренды по названию

Популярные бренды