manualshive.com logo in svg

Badger Meter Dynasonics DFX Series, Руководство пользователя

Поделиться
Скачать
Badger Meter Dynasonics DFX Series Скачать руководство пользователя страница 5

Scope of This Manual

Page 5 

August 2019

DPP-UM-00256-EN-03

SCOPE OF THIS MANUAL

This manual is divided into two main sections:
• 

“Quick-Start Operating Overview” on page 6

 is intended to help you get the DFX flow meter up and running quickly  

Refer to the detailed instructions if you require additional information 

•  The remaining chapters provide a detailed description of all software settings and hardware installation guidance  

MPOOTANT

I

Read this manual carefully before attempting any installation or operation. Keep the manual accessible for future reference. 

UNPACKING AND INSPECTION

Upon opening the shipping container, visually inspect the product and applicable accessories for any physical damage such 

as scratches, loose or broken parts, or any other sign of damage that may have occurred during shipment 

OTEE:

N

If damage is found, request an inspection by the carrier’s agent within 48 hours of delivery and file a claim with the 

carrier

  

A claim for equipment damage in transit is the sole responsibility of the purchaser

 

SAFETY

Terminology and Symbols

 

Indicates a hazardous situation, which, if not avoided, is estimated to be capable of causing death or serious 

personal injury 

 

Indicates a hazardous situation, which, if not avoided, could result in severe personal injury or death 

 

Indicates a hazardous situation, which, if not avoided, is estimated to be capable of causing minor or moderate 

personal injury or damage to property  

Содержание Dynasonics DFX Series

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды