background image

 

PAGE  6 

SETTING DECK HEIGHT

 

2.23  If your machine is equipped with an actuator motor, raise the deck using the raise /lower switch. Refer 

to section 7 (Controls). When deck is raised, set desired height with the deck height control dial, then 

lower deck with the raise / lower switch. 

2.24  If your machine is equipped with a foot pedal, press foot pedal to raise deck, select your desired deck 

height with the deck height dial, then slowly release foot pedal. 

SLOPE OPERATION

 

Slopes are a major factor related to loss of control and tip over accidents, which can result in severe injury or 

death. Operation on all slopes requires extra caution. If you cannot back up the slope, or you feel uneasy on it, 

do not mow it. Bad Boy Mowers recommends always evaluating the terrain and slop conditions prior to 

operating on or near a slope to ensure the mower is operated in a safe manner. Under proper conditions your 

Bad Boy Mower may be able to mow a maximum slope of 5 degrees transversely, across the slope, and a 10 

degree slope if driving up the slope, and a maximum of 15 degrees if driving down the slope. Following are 

some general guidelines Bad Boy Mowers recommends following. 
2.25  Mow up and down slopes, not across. 

2.26  Watch for holes, ruts, bumps, rocks, or other hidden objects that tall grass can obscure. Uneven terrain 

could overturn the machine. 

2.27  Choose a low ground speed when operating the machine on a slope. 

2.28  Do not mow on wet grass, the tires may lose traction. 

2.29  Do not attempt to coast down a slope in the neutral position. 

2.30  Avoid starting, stopping, or turning on a slope. If the tires lose traction, disengage the blades and 

proceed slowly, straight down the slope. 

2.31  Keep all movement on slopes slow and gradual. Sudden changes in speed or direction could cause the 

machine to roll over. 

2.32  Use extra care while operating machine with grass catchers or other attachments: they can affect the 

stability of the machine. Do not use on steep slopes. 

2.33  Do not try to stabilize the machine by putting your foot on the ground. 

2.34  Do not mow near drop offs, ditches or embankments. The machine could suddenly roll over if a wheel 

goes over the edge or the edge caves in. 

2.35  Be aware of what is located at the bottom of slopes. For example: rocks water, cliffs, and roadways. 

CHILDREN 

Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to 

the machine and the mowing activity. NEVER assume that children will remain where you last saw them. 

2.36  Keep children out of the mowing area and in the watchful care of a responsible adult other than the 

operator. 

2.37  Maintain Alertness and turn machine off if a child enters the area. 

2.38  Before and while backing, look behind and down for small children. 

2.39  Never carry children, even with blades shut off. They may fall off and be seriously injured or interfere 

with safe machine operation. Children who have been given rides in the past may suddenly appear in 

the mowing area for another ride and be run over or backed over by the machine. 

2.40  Never allow children to operate the machine. 

2.41  Never leave the key in the ignition, especially around children. 

2.42  Use extreme care when approaching blind corners, shrubs, trees, or other objects that may block your 

view of a child 

Содержание RENEGADE Series

























































Отзывы: