Backyard Discovery Next Generation 5007 Скачать руководство пользователя | Manualshive

Страница: 1 / 88

background image

The Cedar Mountain Swingset

From Backyard Discovery

Backyard Discovery

3001 N Rouse Ave

Pittsburg, KS 66762

www.swingsetsonline.com

Sales: 855-308-6871

Support: 800-856-4445

YOU MUST START HERE!

Use these assembly instructions to begin assembly of your Cedar Mountain swingset.

1.

The Cedar Mountain is made from individually packaged components. Each
component has its own assembly instructions in the box.

2.

Build each component according to the instructions in the respective
component box(es)

except for the Tunnel.

3.

For the tunnel only, you MUST use the instructions in this package. DO NOT USE
THE INSTRUCTIONS IN THE TUNNEL/ ROCK WALL BOX!

4.

Once all components are complete, attach them to the respective towers to
make the Cedar Mountain configuration as shown. Attach the towers together
using the tunnel and the instructions in this package!

5.

The swing beam can be attached to the back of either fort without causing a
play conflict.

6.

Build the rock wall using the original tunnel/rock wall instructions in the box and
attach it to one of the fort openings as directed in the rock wall instructions.

7.

DO NOT INSTALL THE 10’ SLIDE AND THE 8’ SLIDE NEXT TO EACH OTHER! YOU
MUST LEAVE A TOWER WALL PANEL IN PLACE AS A SPACER TO SEPARATE THE
TWO SLIDES. MOUNTING THEM CLOSE WILL CAUSE A PLAY CONFLICT AND
MAY RESULT IN INJURY!

8.

DO NOT MOUNT THE MONKEY BARS ON THE SAME TOWER/SIDE OF THE
TOWER AS EITHER SLIDE. THIS WILL CAUSE A PLAY CONFLICT AND MAY RESULT
IN INJURY!

Meijer.com

1
2
3
...
»

Содержание Next Generation 5007

























































































Отзывы:

Нет отзывов

Похожие инструкции для Next Generation 5007

Бренд: Baby Trend Страницы: 16

Бренд: Backyard Discovery Страницы: 56

Бренд: EINHELL Страницы: 47

Бренд: BABY MONSTERS Страницы: 17

Бренд: Kaiser & Kühne Страницы: 16

Бренд: HAMPTON BAY Страницы: 10

Бренд: Jack-Post Страницы: 11

Deluxe Cushioned Double Swing

Бренд: Hatteras Hammocks Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды