background image

 

DISCLAIMER

Under no circumstances shall the manufacturer or distributor of the Backstopper™CA-5009.II system be 
held  liable  for  consequential  or  incidental  damages  sustained  in  connection  with  the  use  of  the 
Backstopper™ CA-5009.II Rear Parking Assist System.  The Backstopper™ CA-5009.II is designed as a 
safety enhancement device and is in no way intended as a replacement for rear-view mirrors, side-view 
mirrors or physically checking the surroundings when backing a vehicle.  Always check surroundings for 
safety  when  backing  up!    Objects  on  the  monitor  are  closer  than  they  appear.    For  the  installation, 
modification  of the vehicle bumper is required.  It is the sole responsibility of the vehicle owner to check 
and  verify  any  and  all  State  or  Federal  Motor  vehicle  codes  with  regards  to  modifications  of  vehicle 
bumper or any systems in the vehicle.  The manufacturer of the Backstopper™ CA-5009.II assumes no 
liability  or  responsibility  whatsoever  with  regards  modifications  of  the  vehicle  bumper  or  any  other 
equipment in the vehicle. 
 
 
 

 

 

www.crimestopper.com 
[email protected] 
Phone (800) 998-6880 
FAX (805) 581-9500 
 
© 2013 Crimestopper Security Products 

 

 
 
 
 
 
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 

2-25-2013 

Содержание CA-5009.2















Отзывы: