BaBylissPro 4ARTISTS FX8700GBPE, Руководство пользователя

Страница: 4 / 51

6 7
ENGLISH
Please carefully read the safety
instructions before using the
appliance.
SAVE THESE INSTRUCTIONS
adaptateur CA78M
Vibrations < 2,5 m/s²
LpA (dB(A)) < 70
PROFESSIONAL CORD/
CORDLESS CLIPPER
FX8700GBPE - FX8700IBPE –
FX8700RBPE
OPERATING INSTRUCTIONS
1. Before using the clipper for the
first time, charge continuously
for 4 hours. Maximum battery
capacity will only be reached
after 3 charging and discharging
cycles.
2. Make sure the switch on the
clipper is in the OFF position.
Connect the charging jack into
the receptacle on the bottom
of the clipper. Plug the adapter
into any electrical outlet (at
the voltage listed on the label
affixed to the adapter). The
charging indicator will light
up blue to indicate that the
charging has begun. Charging is
complete after 4 hours.
3. The adapter may become warm
while charging. This is normal.
4. Preserving the batteries: To
maintain the optimum capacity
of the rechargeable batteries,
the clipper should be recharged
for 4 hours approximately every
6 months.
5. Make sure the switch is in the
OFF position when the clipper is
not operating.
6. If the charging light starts
to flash rapidly (more than
4 flashes per second) then
the appliance is faulty. If this
happens then please stop
charging and remove the
adapter from the mains and
contact an authorized Service
Center.
FOR DIRECT PLUG-IN
OPERATION
Make sure clipper is off. Connect
charging jack into the receptacle
at the end of clipper and plug the
adapter into power outlet.
ON/OFF SWITCH
To operate, simply slide switch
to ON (marked «I»). To stop
operation, set to the OFF (marked
«0») position.
VERY IMPORTANT : Blades must
be cleaned and oiled on a regular
basis for proper functioning.
Failure to regularly clean and oil
the blades will void the warranty.
USER MAINTENANCE
INSTRUCTIONS
MAINTENANCE OF THE BLADE
Always apply oil to the blades
before and after use. This will
ensure maximum cutting
performance and proper
maintenance. Hold the clipper
away from your body in a
downward position and apply a
drop of BaBylissPro lubricating oil
on the front and sides of the cutter
blade. Wipe off excess oil with a
soft, dry cloth.
Do not pull, twist, or wrap the
supply cord around the appliance.
HOW TO USE COMB
ATTACHMENTS
To use the comb attachments,
turn the clipper to “0” position.
Slide the comb attachment onto
the top of the clipper blade, and
then pull down and over the back
of the blade. To remove, pull up on
the back of the comb attachment
and then pull away from the blade.
REPLACEMENT (REMOVAL) OF
BLADE SET
Taper
A. B.
Small
Moving
Blade
Plastic Oscillator
Step 1. Unplug the unit and adjust
the taper (see illustration A).
Step 2. Remove the screws and
the fixed blade. Save the screws.
Step 3. Lift off the small moving
blade and replace it with the new
one on the plastic oscillator (see
illustration B).
Step 4. Replace the fixed blade
using the screws and lightly
tighten them. Adjust the teeth as
shown in illustration C, to a gap of
0.8 mm to 1.5 mm, and the small,
moving blade as centered and
parallel as possible to the fixed
blade’s teeth.
IMPORTANT NOTE:
The top edge of the fixed blade
must be a minimum of 0.8 mm
higher than the top edge of the
moving blade, as centered as
possible. This is important so that
the moving blade does not come
in contact with the skin.
Be sure to add a few drops of
BaBylissPro lubricating oil to the
blades before running. Don’t
forget to tighten the screws after
the blades have been aligned.
Small
Moving
Blade
Fixe Blade
0.8 mm
C.