1. Carefully unpack the contents of the carton and start the
assembly as close to the final intended position.
2. Set the Drawer Box (A) upside down on a soft, clean
surface.
3. Screw the Drawer Box Feet (B) onto the threaded rods on
the bottom of the Drawer Box by turning them as shown.
4. Turn over the assembled Drawer Box (A).
5. Place 2 of the Short Supports (C) into the french slots
found on the top of the Drawers Box (A) and attach each
of them with 4 screws.
6. Lay the Desk Top (D) upside down on a soft, clean
surface. Insert the other 2 Short Supports (C) into the
french slots found on the bottom of the Desk Top (D) and
attach each of them with 4 screws.
7. Place the Desk Top (D) on top of the Drawer Box (A)
8. Add the Front Leg (E) by screwing its threaded end into
the preassembled nut under the front corner of the Desk
Top (D).
9. Place Back Leg (F) under the back corner of the Desk Top
(D) and screw the 3 Rods (G) into the 3 holes found on the
top of the Desk Top (D).
10. Insert the Long Pipe (H) onto the left side Rod (G) and 2
Short Pipes (
I
) onto the central and right side Rods (G).
11. Insert the Short Shelf (J) onto the central and right side
Rods (G), then, add 2 more Short Pipes (
I
) above the
Short Shelf (J).
12. Take one of the Long Shelves (K) and add it to the
structure by inserting the 3 Rods (G) in the 3 holes of the
shelf. Add 3 Short Pipes (
I
) to the 3 Rods (G) and insert
the second Long Shelf (K).
13. Screw the 3 Bent Pipes (L) to the ends of the 3 Rods (G)
and fix them to the wall with screws, and anchors if
needed.
14. Assembly is complete.
and
attach them by fastening the 2 Bolts and Washers from
the inside of the first drawer .
PARTS INCLUDED
A [1] DRAWER BOX
B [4] DRAWER BOX FEET
C [4] SHORT SUPPORTS
D [1] DESK TOP
E [1] FRONT LEG
F [1] BACK LEG
G [3] RODS
H [1] LONG PIPE
I
[7] SHORT PIPES
J [1] SHORT SHELF
K [2] LONG SHELF
L [4] BENT PIPES
TOOLS NEEDED
ASSEMBLY INSTRUCTIONS
TWO OR MORE PEOPLE MAY BE NEEDED FOR EASY ASSEMBLY
HARDWARE LIST
Step 3
Step 5
Step 6
Step 8
B
A
B t m
to
o
p
To
C
A
E
CARE INSTRUCTIONS
1. Clean periodically by wiping with a soft clean dry cloth.
2. Do not use abrasive cleaners, chemical cleaners, or metal
polishes, as they may damage the finishes.
IMPORTANT SAFETY INSTRUCTIONS
Young children may be injured by tipping furniture and proper installation of the mounting hardware for this item is highly recommended.
When properly installed, this mounting hardware could provide protection against the unexpected tipping of this furniture piece.
Page 1 of 2
Step 7
tt
Bo om
D
C
Fron
ide
s
t
i e
Ba
s
ck d
NO.
ITEM
DESCRIPTION
QTY.
1
2
Screw
25 pcs.
Plastic Anchor
12 pcs.
3
4
Bolt
2 pcs.
Washer
2 pcs.
A [1] PHILLIPS HEAD SCREW DRIVER (Not provided).
B. [1] SPANNER (Provided)
D
I N D U S T R I AL P I P E S I N G L E D E S K W I T H D R A W E R S
